Search found 20 matches

Return

by Chris_MIRA
Fri Sep 20, 2013 10:20 am
Jump to forum
Jump to topic

Re: EB076 help

All up and running now!
thanks for your help :-)
by Chris_MIRA
Wed Oct 30, 2013 3:16 pm
Jump to forum
Jump to topic

Motor control bug?

Hi, In FC 6, there appears to be a bug that puts the stepper motor pulse out of sequence on the MIAC (works OK in simulation). If connected conventionally with windings A B C D the motor fights itself but if you swap windings B and D the motor works. As a check, the same code in V5 and windings conn...
by Chris_MIRA
Mon Mar 17, 2014 4:01 pm
Jump to forum
Jump to topic

Re: GOTO problem in macro?

Thanks!
That's great, supplementary code copied , pasted and all compiling fine :D :D :D
Thanks for all your trouble!
Regards,
Chris
by Chris_MIRA
Thu May 01, 2014 7:42 am
Jump to forum
Jump to topic

Re: GOTO problem in macro?

Great! Got it now (Sorry) I haven't used a C Icon before and had missed your insertion at the top of the MACRO!
Thanks for all your help!
Regards,
Chris
by Chris_MIRA
Thu May 08, 2014 8:10 am
Jump to forum
Jump to topic

LCD simulation not clearing

When stepping through a programme in simulation a couple of times, txt on screen is not cleared as you go through the DISPLAYCLEAR macro, it only seems to clear later in the programm if something else is written to the display. Problem seen on MIAC and on EB006 / EB005 boards using FC6.06. Bug repor...
by Chris_MIRA
Thu May 08, 2014 11:09 am
Jump to forum
Jump to topic

Re: LCD simulation not clearing

Hi,
"Yes" your test seems to work OK on my machine, Ive attached my programme using a MIAC, and added a comment just above the last macro in MAIN "DisplayClear" which should remove the "Working" message
Regards,
Chris
by Chris_MIRA
Fri Oct 03, 2014 10:14 am
Jump to forum
Jump to topic

Re: ECIO DS pic

To reply to your question about tutorials on line, It would be very nice to have a You Tube tutorial on how to set up and simulate a PID controller using the ECIO ds pic! :D
Regards,
Chris
by Chris_MIRA
Tue Oct 14, 2014 10:38 am
Jump to forum
Jump to topic

Re: Table in supplimentary code

That is very cool!
Thanks very much for both your help and speed of reply!
Regards,
Chris
by Chris_MIRA
Wed Dec 10, 2014 9:43 am
Jump to forum
Jump to topic

Re: FC6 dsPIC compiling to hex problem

Yes! all sorted now.
Thanks for your help :D
Chris
by Chris_MIRA
Thu Feb 05, 2015 3:18 pm
Jump to forum
Jump to topic

Re: EB006V9 power up time

Hi, Okay, attached are two programmes, a simple test programme and a more complex on I use for collecting temperature data, Im using a PIC 16F1937 for both, plugged into the EB006V9 board. The board is powered with 12 volts, either from a matrix work station (when on my desk) or from a vehicle syste...
by Chris_MIRA
Mon Feb 16, 2015 10:03 am
Jump to forum
Jump to topic

Re: ECIO PIC

Using the patch system sort of works but still doesn't solve the issue of taking two ports up (very valuable real-estate!). Could you let me know when the bug is fixed?
Regards,
Chris
by Chris_MIRA
Thu Feb 26, 2015 2:45 pm
Jump to forum
Jump to topic

Re: Ghost ICD comunication with ECIO ds PIC

Okay, All older file versions deleted, new file downloaded and copied to the right folder, only one file now in that folder with the correct name. FC6 re-started and the attached programme compiled and flashed to device using ghost and Flowkit (again all relevant icons showing green to indicate ghos...
by Chris_MIRA
Mon Mar 02, 2015 3:11 pm
Jump to forum
Jump to topic

Re: Reading CAN ID issue

Hi, Please see attached file, this contains a work around that seems to function okay, Im using the component macros "GET RX id Hi" and "GET RXid Low", then diving the low by 32 and multiplying the Hi by 8 before adding together to get the right Rx id. As said this work around do...
by Chris_MIRA
Tue Nov 03, 2015 8:38 am
Jump to forum
Jump to topic

Re: DS PIC flowcode not compiling

Are... thanks :-) Just another "Im Stupid" fault... I get a lot of them!
Thanks for sorting me out so quickly!

Regards,
Chris
by Chris_MIRA
Wed Jan 06, 2016 3:09 pm
Jump to forum
Jump to topic

Re: Arduino Nano and CAN coms (2)

Hi LeighM, Im using a commercially available CAN module for the arduino Nano as it is to go into a product and is physically smaller. Im sure you have identified the problem as the oscillator on the module is 8Mhz rather than 20. As the Arduino CAN modules are very common and all seem to have the 8M...
by Chris_MIRA
Tue Dec 06, 2016 12:37 pm
Jump to forum
Jump to topic

Re: Pic Uc32 not compiling to chip

Yey, all working well!!!

Thanks again very much for your help!
Really impressed with both your technical help and the speed of response to messages! :D :D

Regards,
Chris
by Chris_MIRA
Mon Aug 13, 2018 12:29 pm
Jump to forum
Jump to topic

Re: Down loading programme to MEGA 2560

Thanks Benj :D
Now I know, Ill just go-buy a R3 version!
Regards,
Chris
by Chris_MIRA
Wed Jan 23, 2019 4:09 pm
Jump to forum
Jump to topic

Re: Variant on old problem downloading to arduino MEGA R3

Hi,
Thanks to all for helping! Issue now seems to be sorted (including the update check button).

best regards,
Chris :D :D :D
by Chris_MIRA
Fri Feb 01, 2019 11:21 am
Jump to forum
Jump to topic

Opening historical programmes in FC 8

Hi, When opening historical programmes (written in FC 6 or FC7) with FC8, the port configuration for CAN module is automatically set to FC8 default (usually port e pins XX XX regardless of the actual device) and the original old port settings is lost. Is there anyway to recover or preserve the origi...
by Chris_MIRA
Tue Feb 05, 2019 10:59 am
Jump to forum
Jump to topic

Re: CAN CheckRx(0) Not working?

Hi,
With the V8 spi set to channel 1, everything works :D . Sorry I hadn't noticed this difference so had not tried it!
CAN works fine with the 8MHz in the arduino at 500baud.
Thanks again to MARTIX and everyone for your help!

Regards,
Chris