Search found 24 matches

Return

by saschech@gmx.de
Tue Jan 04, 2011 11:56 am
Jump to forum
Jump to topic

Re: Eeprom compiler error on PIC16F946

hello dannyvanneijenhoff

show the picture...

select in the viewe tab > panel and > panel properties >then click on the ...(3 points) on the right!!! open the window

regards Wolfgang
by saschech@gmx.de
Thu Jan 06, 2011 4:10 pm
Jump to forum
Jump to topic

Re: Incrementing in EEPROM

Hello

Cheer up!

have a look at xxxxxxxxxxxxx modify.

Regards wolfgang
by saschech@gmx.de
Thu Jan 06, 2011 10:58 am
Jump to forum
Jump to topic

Re: Incrementing in EEPROM

Hello nmindana

Work in the eeprom_macro instead 0 >>>>> global int variable "adress_finger" (adressfinger = adressfinger +1 or adressfinger = 2 .........)
so you can update variable "adressfinger" on all location inside your code.

Regards Wolfgang
by saschech@gmx.de
Thu Jan 06, 2011 7:07 pm
Jump to forum
Jump to topic

Re: Incrementing in EEPROM

Hello

In 1 eeprom-adresse you can only store 1 number(0to255 0x00 to 0xff) 1= 0x31 ; 2= 0x32 ; *= 0x2a....

so for 31sec you must take 2 adresses ad0= 1= 0x31 ; ad2= 3 = 0x33
for 24:30:11 you must use 6 adresses

Regards Wolfgang
by saschech@gmx.de
Wed May 11, 2011 8:03 am
Jump to forum
Jump to topic

Re: I2C

Hello Mario

have a look to the datasheet....

With the rw bit 1101 000_1 = 0xd1

http://datasheets.maxim-ic.com/en/ds/DS1307.pdf

regards wolfgang
by saschech@gmx.de
Thu Sep 29, 2011 4:29 pm
Jump to forum
Jump to topic

Re: a little help please

Hallo johndobson Ich würde für E- = elektronik setzen da es für mich als Wort keine direkte Aussage tätigt System = wird in deutsch verstanden ( z.b mehrere Aggregate vereinigt) designe software = Entwicklungs Software E-system design software = elektronik System Entwicklungs Software Hoffe es hilft...
by saschech@gmx.de
Fri Jan 20, 2012 10:17 am
Jump to forum
Jump to topic

Re: V5 Upgrade ?

Hi jorgen

On start with V5 ,i have had the thame emotion,bat after a short time it was ok.
With the mouse you can change the size and the position of the bubble for a better read.....
so i think it is better to read.

Regards Wolfgang
by saschech@gmx.de
Sun Feb 12, 2012 10:22 am
Jump to forum
Jump to topic

Re: mplab with v5 hex

Hello

I have also no success burn with ICD3-MPLAB.With V4 no probs.
I can burn, but the cod dont work on hardware>>>>burn inside v5 with PicKit3 The thame code, all ok.

Regards Wolfgang
by saschech@gmx.de
Sun Feb 19, 2012 10:41 am
Jump to forum
Jump to topic

Re: 16f1829 dont work

Hello brandonb

The MPLAB say`s if i want use these chip........no support

Pickcit3 , I self work with these from China(less in the price)
http://www.ebay.de/sch/i.html?_from=R40 ... Categories

Regards Wolfgang
by saschech@gmx.de
Sat Mar 17, 2012 6:54 pm
Jump to forum
Jump to topic

Re: dsPIC EEPROM

Hello beambase I dont no,the v4dspic have these updates inside.... I have these files become in the beta-phase Inthe moment,I work with a 30F6012A with no probs on eeprom(only adr. 0 work not correct) rename the org-files to xxx.xxx_org and copy the updat files in the folder,so you can change alltim...
by saschech@gmx.de
Mon Apr 02, 2012 8:27 am
Jump to forum
Jump to topic

Re: Quadrature and 18F4455

Hello Bobw

Have a look inside the pdf.I work with toggle interruption.Work well.

Regards Wolfgang
by saschech@gmx.de
Mon Nov 05, 2012 11:04 am
Jump to forum
Jump to topic

pickit3 programmer

Hello After programm with pickit3 my board wait in reset........ In the newest "readme" i found -L (after programming run) all work ok. Also i read in a 64bit system there are problems.... 5. Known Problems ---------------------------------------------------------------------------- ICD3-2...
by saschech@gmx.de
Mon Nov 19, 2012 2:23 pm
Jump to forum
Jump to topic

Re: convert to string dspicV5.4

Hello

all return,after a Long search :

I read the fram FM25V5 in the READ-mode dos not read bit8 korrekt.....
I use the FSRD mode and all work ok on my Hardware

Regards Wolfgang
by saschech@gmx.de
Sun Jan 20, 2013 10:23 pm
Jump to forum
Jump to topic

Re: Advice Sought: Flowcode V5 with ICD3 ?

Hello With the V4 for pic and a build projekt with the MPLAB you can compile with payed sourceboost compiler inside MPLAB >> program with ICD3 or PICkit3. I do These with success!!! With V5 I dont no for the vor include files....I have the question in the Forum,but not answer....no success.....so I ...
by saschech@gmx.de
Fri Jun 14, 2013 9:21 pm
Jump to forum
Jump to topic

Re: PIC18F45K22 programming fails

Hello fotios

ICD2 dont Support the 18F45K22.At ebay pickit3 for 23€.......;
I order one no probs.....

Regards wolfgang
by saschech@gmx.de
Fri Oct 04, 2013 12:37 pm
Jump to forum
Jump to topic

Re: Programmers

Hi JFinlayson Download and install the MPLAB 8.92 ! (not the mplabx) After open the mplab as blank goto > Configure and select > device > your pic >open programmer and select your type of prog. It must Show the Output window Then open File > Import > the **.exe in your flocode Folder You can schow i...
by saschech@gmx.de
Sat Sep 17, 2016 8:07 pm
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

hello I remember: Re: Problem with Flowcode SPI macro with accelerometer compo Postby Benj » 11 Jan 2013, 14:30 Hi Wolfgang, ""Steve - who has recently left Matrix - was the sole developer on PPP"" Unfortunately Steve has left the company but he has not been responsible for the P...
by saschech@gmx.de
Sat Sep 17, 2016 6:23 pm
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

hello steve

Are you back to matrix or a new employee with the thame name?

Regards wolfgang
by saschech@gmx.de
Fri Sep 16, 2016 9:32 pm
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

hello steve

any news???

Regards wolfgang
by saschech@gmx.de
Fri Sep 02, 2016 6:16 pm
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

hello

any news? the date is 02.09.2016............

Regards wolfgang
by saschech@gmx.de
Mon Sep 19, 2016 11:17 am
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

Hi Steve

At the time FC3 , FC4 and FC5 I remember your word was reliabl,
but in the moment I think your words are not concrete.
At the time of FC6 I switch to "c" ....
With FC7 I think matrix have mutch more problems....
Hope the 30day version comes in near time

Regards Wolfgang
by saschech@gmx.de
Mon Sep 19, 2016 3:27 pm
Jump to forum
Jump to topic

Re: FC7 Pro Off-line Activation Fails

Hello Benj

"The release is ready and being tested this week and I am confident it will be released next week."

These were Stev´words two weeks ago.......

Regards Wolfgang
by saschech@gmx.de
Fri Mar 31, 2017 4:21 pm
Jump to forum
Jump to topic

Re: error code -1

Hi

After do all new,show all ok on the display.

Thank you