Search found 9 matches

Return

by Mark
Thu Jul 21, 2011 9:47 pm
Jump to forum
Jump to topic

Re: gLCD with Formula Flowcode

gLCD Works fine on FF :) Port D using e-blocks connector and 9v PP3 from 5v (battery ground) to gLCDVPWR (battery +ve).

Thanks.
by Mark
Sun Aug 28, 2011 8:38 am
Jump to forum
Jump to topic

Re: SPI Memory, 25LC1024 and SPI Component

Hi Ben, I have pulled together a suite of 10, tested, subroutines to utilise the functions of the 25LC1024 Chip. The attached code should be self explanatory. It includes the Macros: Enable Write Disable Write Read Write - With 6ms delay Write - With polling to see end of write Read Status Write Sta...
by Mark
Thu May 17, 2012 10:20 pm
Jump to forum
Jump to topic

Re: gLCD with Formula Flowcode v5

Ben, Thanks, this works fine. For other users: 9v pp3 from battery -ve to 5v out on buggy, battery +ve to VPWA on EB058 board. 5v+9v=14v :) Buggy connected to EB058 gLCD with standard 9in D type jumper, short version preferable. Routine below, lights screen, clears it and prints Hello. Slowish, so b...
by Mark
Wed May 30, 2012 3:07 pm
Jump to forum
Jump to topic

Re: Memory usage by macro variables

Benj, Jonny, Thanks for both your inputs. My feeling with Flowcode 5 is that I am reaping the benefits mostly from improvement of current functionality and the addition of further functions/peripherals is becoming more and more esoteric. Hence, continuing to work on improved functionality of existin...
by Mark
Sat Aug 25, 2012 10:35 pm
Jump to forum
Jump to topic

Flowcode v5.4 PIC18F47J53 Code Error

Flowcode v5.4 PIC18F47J53 Code Error "SOS" :-o (rather than "OS" :-) ) The code both for the FCD file and the Interrupt set-up code file appear to have an error: //Clock //Interrupt: Enable TMR1 st_bit(intcon, PEIE); st_bit(t1con, TMR1ON); cr_bit(t1con, TMR1CS0); st_bit(t1con, TM...
by Mark
Mon Mar 18, 2013 9:42 pm
Jump to forum
Jump to topic

Flowcode/e-blocks on TV

Take a look at: http://www.bbc.co.uk/iplayer/search?q=You%20Too%20Can%20Be%20an%20Absolute%20Genius It is targeted for schools and valid for the next 5 days. About half way through, e-blocks programmed using Flowcode 5 are used. The heater is a 15ohm 1w resistor run off a relay using the 14v spur fr...
by Mark
Mon Mar 10, 2014 9:58 am
Jump to forum
Jump to topic

Re: Flowcode v6 Tutorial Videos for v5 user

Hi Ben, I have just started with Flowcode 6 and am very impressed with the videos. Two initial reactions jump out for me, and therefore may be helpful to you. Whilst there is a video talking about the differences between Flowcode 5 and 6 I would like to see (maybe it is there already?) A hands-on ho...
by Mark
Tue Jun 10, 2014 7:05 pm
Jump to forum
Jump to topic

PicKit3 Command Line Extensions - Power

I have had a look at the excellent wiki (and trawled the Forum, so sorry if it already there). http://www.matrixtsl.com/wiki/index.php?title=Supporting_Third_Party_Programming_Tools and at the microchip datasheet (attached). From this I expected changing, the FC 6 Programmer Parameters to: -P$(chip)...
by Mark
Wed Jun 25, 2014 4:08 pm
Jump to forum
Jump to topic

Re: Flowcode v6.0.9 Live

Thanks guys. Yes, problem with error 120 solved with a restart. I suggest forcing a restart after install as many programs do not require restart these days. Barge pole and Windows 8, Yes, I mistakenly installed the Windows 8.1 update. Not so much an update as yet another way of working. It insisted...