Matrix user forums

thanks ! currently looking at the PWM examples, with ADC . need to get a POT , and a momentary switch, couple resistors. looked at the pdf for the pic18f26j50, but could not find , where the PWM1 / 2 would be ? on the PWM example, would want to add an LCD, as to display the ADC state, -> temp sensor...

PWM output pin on ECIO-28 ?

tried the ADC / PWM example,
can't find, what pin it would use to output the pwm signal ?
how does that work ?

update ... got the ECIO-28 in, and the other stuff,.. first , had to find a USB cable, note -> the others use a mini, not full size,... tried the example , could not get it to work, syntax error,... next day, radio-shack, get an led an resistor,... loaded the LED example, .... did not work,... took ...

thanks ! I'll order the baseboard for the ECIO - EB-005 LCD - the momentary switch board - flowcode home version, so I could use the pic18f14k50, later/final - potentiometer any recommendations for a third party LED, seven segment, 2/4 digit , that can work with ECIO-28 ? or small LCD ? in my housin...

Thanks for the recommendations ! I'am getting also the ECIO-28 board ! did look at the E-Blocks, but could not find it in flowcode !? and for the EB-005 LCD, it does not say if it works with free/home version !? Most LCD's use a serial interface SPI or I2C , and that only works with the pro version ...

any recommendations , for a LCD to work with the free version of flow code ? for shops microcontrollershop or sparkfun / mouser / in usa preferred . my initial shopping list included <pre/> PIC18F26J59 Prototype Board, 8x LEDs, USB, ICSP, UEXT PIC18F14K50 USB-to-RS232 Module, UEXT, ICSP Microchip PI...

thanks John ! forum is great ! Do think, those things, Matrix needs to address!!!! note for the Atmel ATTINY85, has a built-in Temp sensor, gets addressed through ADC. minimum for my project 1 temp sensor 1 momentary switch 1 PWM output later on, multiple everything,... probably have parts and board...

in the search for the holy grail to get started ,... FYI, notes, shout ,... still could not find any offical documentation, on using temp sensors with flowcode, NTC, I2C, 1-Wire,... tmp102, lm75, DS1820,... yes I will get it going with the forum,.... still think , this needs to be addressed . mikroe...

that is really bad !!!! that means , anybody with a pinguino board , is left out. !!!! get it done ASAP ! all the available dev boards, should be priority ! Hi Wolfgang, It is something we are considering (along with support for the 16-bit PIC24, dsPIC30 and dsPIC33 series devices), but we have no i...

what I meant to ask, Free, home, pro version ?! can I use the Free version, with a 1-wire Temp Sensor ?? thanks, Rob Hi, Although FC v4 has the facility that you are looking for but I will suggest you to go for V5..As it is new and MM people and forum member concentrate highly on this version.. what...

thanks for the reply ! I will start with the TMP35, and then get some microchip temperature sensors. what Flowcode version do I need ? TMP35 + pwm ? I2C temp sensor + PWM ? 1-wire Temp sensor + pwm ? IRD, Infrared ? basically it's going to be for a LED driver, to temperature throttle . got the pic 3...

Is Flowcode any good for Beginners ? I want to do some temperature measurements , and could not find anything to get started !? not even an ready to use Eblock ? in the Programm , could not find a simple component, like temp sensor ?! temp sensors, come in resistors, 1-wire, I2C , tmp35 ,...etc coul...