Search found 12 matches
- Wed Feb 13, 2013 11:32 pm
- Forum: Flowcode V5
- Topic: Getting Started Help: LED Array based on Single Integer
- Replies: 6
- Views: 4000
Re: Getting Started Help: LED Array based on Single Integer
Hi If you add an eeprom component then read /write to it in code you should see the changes on the panel, search the forums as there are a couple of eeprom write examples which simulate well Regards Dazz I noticed that but it doesn't apply when developing a system that requires I2C protocol. -NGM
- Wed Feb 13, 2013 10:27 pm
- Forum: Flowcode V5 Suggestions
- Topic: I2C Slave Simulation
- Replies: 3
- Views: 6957
I2C Slave Simulation
It would be great if one could add an I2C Slave device (keep it simple, let's say you offer us an EEPROM for now) that can be simulated in the panel. Basically an I2C device that we can read and write to and manually edit it's contents if desired. This would offer a little more power than the Bytes ...
- Wed Feb 13, 2013 10:20 pm
- Forum: Flowcode V5
- Topic: Getting Started Help: LED Array based on Single Integer
- Replies: 6
- Views: 4000
Re: Getting Started Help: LED Array based on Single Integer
Dear ngm Try this. Jan Lichtenbelt Hi Jan, Thanks for the example. Let me comment piece by piece in sections: Initialize I2C | Start I2C | I think there needs to be another I2C operation here in which we issue the address that we want to read from is there a way to simulate an EEPROM in fc? | Read ...
- Wed Feb 13, 2013 9:28 pm
- Forum: Flowcode V5 Suggestions
- Topic: Add "Else If" to Decision Block
- Replies: 2
- Views: 7469
Add "Else If" to Decision Block
Was excited to try out Flowcode and was disappointed to see no "Else If" equivalent in the Decision block. I don't know how Flowcode is built but I would hope this is a relatively non complicated feature to add. Right now, one needs to use multiple Decisions daisy chained after one another which is ...
- Wed Feb 13, 2013 8:49 pm
- Forum: Flowcode V5
- Topic: Getting Started Help: LED Array based on Single Integer
- Replies: 6
- Views: 4000
Re: Getting Started Help: LED Array based on Single Integer
Just purchased the full version.Even though you have posted in 'Flowcode V5 Free Edition' section are you using Flowcode V5 Free?
If so you will be unable to compile Flowchart that uses I2C to hex or send to your target device via EB006 programming Eblock for example.
-NGM
- Wed Feb 13, 2013 8:45 pm
- Forum: Flowcode V5 Free Edition
- Topic: How to implement "else if" in Decision
- Replies: 7
- Views: 11474
Re: How to implement "else if" in Decision
So I basically need to hand code this in C? It's not that difficult, but I thought this would be a basic feature in Flowcode.
-NGM
-NGM
- Wed Feb 13, 2013 8:42 pm
- Forum: Flowcode V5
- Topic: Is the AVR Dragon Programmer Supported?
- Replies: 6
- Views: 4464
Re: Is the AVR Dragon Programmer Supported?
There are some examples on this page, not sure if it is enough.
http://support.atmel.com/bin/customer.e ... try&id=686
Despite being in the free forum, we now own a full AVR Flow Code 5 version license.
-NGM
http://support.atmel.com/bin/customer.e ... try&id=686
Despite being in the free forum, we now own a full AVR Flow Code 5 version license.
-NGM
- Sun Feb 03, 2013 6:56 am
- Forum: Flowcode V5 Free Edition
- Topic: How to implement "else if" in Decision
- Replies: 7
- Views: 11474
Re: How to implement "else if" in Decision
From the documentation it is looking like I do need to use the switch block, however operators like =, >, <, etc... don't seem to work here. In addition, only constants appear in the drop down, it does not list the Global variables. This is what I thought would work, but my syntax is wrong: http://i...
- Sun Feb 03, 2013 6:32 am
- Forum: Flowcode V5 Free Edition
- Topic: How to implement "else if" in Decision
- Replies: 7
- Views: 11474
How to implement "else if" in Decision
I noticed a simple ability to create "if" statements with the Decision block, but I can't figure out how to do multiple conditions without using multiple decision blocks. In C, one can write an if statement with multiple else if's but I don't see that option here. Maybe the switch would be more usef...
- Sun Feb 03, 2013 2:21 am
- Forum: Flowcode V5
- Topic: Getting Started Help: LED Array based on Single Integer
- Replies: 6
- Views: 4000
Getting Started Help: LED Array based on Single Integer
Here's a little pseudo code for what I am looking to do and could use some help implementing this in flowcode. Do I need to use a switch, a decision and a calculation for this? Read an integer over I2C and store as my_value If (my_value < 26){ LED1 = ON LED2 = OFF LED2 = OFF} else if (my_value > 26 ...
- Wed Jan 30, 2013 6:20 pm
- Forum: Flowcode V5
- Topic: Is the AVR Dragon Programmer Supported?
- Replies: 6
- Views: 4464
Re: Is the AVR Dragon Programmer Supported?
I apologize, it was an issue with the refresh in my browser.
-NGM
-NGM
- Wed Jan 30, 2013 5:27 pm
- Forum: Flowcode V5
- Topic: Is the AVR Dragon Programmer Supported?
- Replies: 6
- Views: 4464
Is the AVR Dragon Programmer Supported?
Is the AVR Dragon Programmer and ICD supported?
-NGM
-NGM