Search found 99 matches
- Wed Jun 03, 2020 1:28 pm
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Hello Martin, Hello Steve, yes in between I could Isolate the Problem. My program with the interrupt was created with FC6. But I have use FC8 and compiled with V2.00 and the Problem came up I used a differnt PC with FC8 and 1.45 Compiler and the Problem was present too. So indeed my Problem is not r...
- Sat May 30, 2020 8:51 am
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Hello Martin, Hello together, today I belive I found a Problem with this Compiler upgrade to 2.0 or greater. I have a program wit a UART Interrupt routine at a PIC18F6722. It Looks that the Interrupt ist not activated inside the chip anymore. Also going down to Compiler 1.45 does not solve the Probl...
- Mon May 11, 2020 8:00 pm
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Hello Martin, yes i can confirm the 100% mark bug. At 1.45 I had already a message saying 100.8% and I was able to prog the device with the hex file without any problems. Plus everything was running fine. If you look at the progging tool, in my case it is a old Pic Kit-2 you see that Version 2.2 is ...
- Mon May 11, 2020 4:03 pm
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Hi Martin, I followed your Installation procedure and FC8 compiling is running. Below a result with the new XC8 Version 2.2 and the old Version 1.45. I picked this fully over 100% loaded old FC8 source just to compare. XC8 Compiler Version 2.20 Memory Summary: Program space used 6F2Dh ( 28461) of 80...
- Sun May 10, 2020 8:46 am
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Many thanks Martin for the explanation.
BR
Dirk
BR
Dirk
- Thu May 07, 2020 10:40 pm
- Forum: Programming Tips & Tricks
- Topic: Using XC8 V2.00 or greater with Flowcode 8
- Replies: 23
- Views: 20301
Re: Using XC8 V2.00 or greater with Flowcode 8
Hello together,
Hello Martin,
many thanks for the reply. Since my Pic8 Compiler Version is 1.45 it seems that first this needs to get updated.
Is there any discription how to install Version 2.xx Compiler?
Changing the Batch files is clear to me.
THX
Dirk
Hello Martin,
many thanks for the reply. Since my Pic8 Compiler Version is 1.45 it seems that first this needs to get updated.
Is there any discription how to install Version 2.xx Compiler?
Changing the Batch files is clear to me.
THX
Dirk
- Thu May 07, 2020 2:44 pm
- Forum: Flowcode V8
- Topic: signed/unsigned int 64 inside FC8
- Replies: 3
- Views: 2409
signed/unsigned int 64 inside FC8
Hello FC Team,
ist it possible to create a variable int 64 signed and unsigned inside FC8?
BR
Dirk
ist it possible to create a variable int 64 signed and unsigned inside FC8?
BR
Dirk
- Thu May 07, 2020 2:41 pm
- Forum: Flowcode V8
- Topic: Flowcode 8 crash
- Replies: 35
- Views: 17189
Re: Flowcode 8 crash
Hello together,
I´m running now FC8 in Version 8.2.2.15 over 10 days and the Problem with the crash did not came back.
May it looks that the problem is fixed.
BR
Dirk
I´m running now FC8 in Version 8.2.2.15 over 10 days and the Problem with the crash did not came back.
May it looks that the problem is fixed.
BR
Dirk
- Sun Apr 12, 2020 3:54 pm
- Forum: Flowcode V8
- Topic: Flowcode 8 crash
- Replies: 35
- Views: 17189
Re: Flowcode 8 crash
THX Victor, I will check your solution. I had the Problem already twice. I deleted the Reg Key after the first case and installed FC8 again. This was running until yeserday. Then i deleted yesterday only the Reg Key... ...until now FC8 is running again and there is a new Reg Key again. As far as I r...
- Sat Apr 11, 2020 10:34 am
- Forum: Flowcode V8
- Topic: Flowcode 8 crash
- Replies: 35
- Views: 17189
Re: Flowcode 8 crash
Hi, I have the same problem. FlowCode crashes and Windows shuts down. The crash from FlowCode comes randomly if I click something in FlowCode. This I have since I bought V8. Now I can’t even start FlowCode. The “start” logo is been seen and then it disappears and FlowCode won’t start anymore. I hav...
- Fri Dec 06, 2019 10:44 pm
- Forum: Flowcode V8
- Topic: XC Compiler Pro mode
- Replies: 10
- Views: 7352
Re: XC Compiler Pro mode
Many thanks guys for your Feedback.
I think for the first time I will use the non pro Version that cam with FC.
The XC Compiler is much faster then my old Boost-C of FC6.
The XC code is smaler too compared with Boost-C
BR
Dirk
I think for the first time I will use the non pro Version that cam with FC.
The XC Compiler is much faster then my old Boost-C of FC6.
The XC code is smaler too compared with Boost-C
BR
Dirk
- Thu Nov 28, 2019 9:42 pm
- Forum: Flowcode V8
- Topic: XC Compiler Pro mode
- Replies: 10
- Views: 7352
XC Compiler Pro mode
Hello FC Community, I just bought/upgraded to FC8 from FC6 and made my first steps. Regarding the 8Bit XC Compiler I get the following message: You have compiled in FREE mode. Using Omniscient Code Generation that is available in PRO mode, you could have produced up to 60% smaller and 400% faster co...
- Tue Aug 20, 2019 8:49 pm
- Forum: Flowcode V6
- Topic: FC6 Boost C Compiler licence problem WIN-10
- Replies: 0
- Views: 6736
FC6 Boost C Compiler licence problem WIN-10
Hello Flow Code Team, I think I have a Problem with my FC6 professional licence running under WIN-10 Under Win-7 my licence is detected correctly running the compile process i see the following message: Licensed to FlowCode User under Single user Pro License for 1 node(s) Limitations: PIC18 max code...
- Fri Dec 07, 2018 3:33 pm
- Forum: Flowcode V6
- Topic: FC6 with PIC18F2420 EE-Prom Problem
- Replies: 11
- Views: 8476
Re: FC6 with PIC18F2420 EE-Prom Problem
Hello together,
problem solved. Somtimes the Problem is sitting in front of the PC!!
The mistake was that the EE-Prom Write function was not reached by the Programm.
BR
Dirk
problem solved. Somtimes the Problem is sitting in front of the PC!!
The mistake was that the EE-Prom Write function was not reached by the Programm.
BR
Dirk
- Fri Dec 07, 2018 2:51 pm
- Forum: Flowcode V6
- Topic: FC6 with PIC18F2420 EE-Prom Problem
- Replies: 11
- Views: 8476
Re: FC6 with PIC18F2420 EE-Prom Problem
Hi Ben, hope you are well. I must recall this old Topic again because I tested today a new PIC with EE-Prom It is a PIC18F2520. I observed the same Problem that I can`t read an write to the EE-Prom. Maybe there is also updated PIC18F2520 Definition file needed too. I would apreachiate if you could t...
- Mon Nov 19, 2018 2:43 pm
- Forum: Flowcode V8
- Topic: Supported all PIC Devices in FC8
- Replies: 2
- Views: 2525
Re: Supported all PIC Devices in FC8
Many thanks Ben.
This is the list I was looking for!!
BR
Dirk
This is the list I was looking for!!
BR
Dirk
- Sun Nov 18, 2018 11:49 pm
- Forum: Flowcode V8
- Topic: Supported all PIC Devices in FC8
- Replies: 2
- Views: 2525
Supported all PIC Devices in FC8
Hello Flow Code Team,
I´m looking for a PIC Controller device list that is supported in FC8.
From Pic 8 to 32.
I can`t find anything in the product discription.
BR
Dirk
I´m looking for a PIC Controller device list that is supported in FC8.
From Pic 8 to 32.
I can`t find anything in the product discription.
BR
Dirk
- Mon Feb 05, 2018 6:44 pm
- Forum: Flowcode V6
- Topic: More then 8 Servos??
- Replies: 3
- Views: 3415
Re: More then 8 Servos??
Thx Ben,
I give you a commitment to buy a FC8 Prof. Version if this goes in as a feature.
In this context please considder a 16Bit resulution for the servo signal too.
BR
Dirk
I give you a commitment to buy a FC8 Prof. Version if this goes in as a feature.
In this context please considder a 16Bit resulution for the servo signal too.
BR
Dirk
- Fri Feb 02, 2018 11:20 pm
- Forum: Flowcode V6
- Topic: More then 8 Servos??
- Replies: 3
- Views: 3415
More then 8 Servos??
Dear Matrix Team, i have a short question. Is it possible to have more then 8 Servos for example under ds30F6011A control. In simulation I can activate two servo controler running a setup with more then 8 servos (for example 12 Servos). This works..... You can select/define controller 1 and 2. :D Tr...
- Fri Feb 02, 2018 12:48 am
- Forum: Flowcode V6
- Topic: LUT Component not working with PIC30F3012
- Replies: 11
- Views: 8304
Re: LUT Component not working with PIC30F3012
Hello Leigh,
many thanks!! Great Support!! It works perfect the new LUT component file.
BR
Dirk
many thanks!! Great Support!! It works perfect the new LUT component file.
BR
Dirk
- Thu Feb 01, 2018 1:34 am
- Forum: Flowcode V6
- Topic: LUT Component not working with PIC30F3012
- Replies: 11
- Views: 8304
LUT Component not working with PIC30F3012
Hello FC Team, I belive I discovered a Problem with FC6.1.3.2 and 16bit dsPIC30F3012. If you compile the attached FC file you will get the follwing error message: PIC30F3012 LUT Error bigger 0xff.c:74: warning: large integer implicitly truncated to unsigned type The message will dissapear if all LUT...
- Sun Nov 26, 2017 10:47 pm
- Forum: Flowcode V6
- Topic: PIC18F2420 not sending STRING via UART
- Replies: 2
- Views: 2806
Re: PIC18F2420 not sending STRING via UART
Hi Leigh,
many thanks!! Yor solution works.
Great Support.
BR
Dirk
many thanks!! Yor solution works.
Great Support.
BR
Dirk
- Thu Nov 23, 2017 8:05 pm
- Forum: Flowcode V6
- Topic: PIC18F2420 not sending STRING via UART
- Replies: 2
- Views: 2806
PIC18F2420 not sending STRING via UART
Hello community, I found a strange things with the Serial hardware UART of a PIC18F2420. If I want to sent a string lets say "Hallo" out of the UART at the chip nothing happens. No bytes comming out (SentString funktion) If I sent a byte or group of Bytes the with SentChar funktion the UART works co...
- Tue Nov 21, 2017 12:15 pm
- Forum: Flowcode V6
- Topic: UART with two differnt baudrates
- Replies: 8
- Views: 8220
Re: UART with two differnt baudrates
Hi Ben,
very good. Many thanks this is the Point I was looking for.
BR
Dirk
very good. Many thanks this is the Point I was looking for.
BR
Dirk
- Mon Nov 20, 2017 8:51 pm
- Forum: Flowcode V6
- Topic: UART with two differnt baudrates
- Replies: 8
- Views: 8220
Re: UART with two differnt baudrates
Hi Ben, your are so right!! Great help!! Sometimes it is hard to see things that are in front of you/me. ChangeHWBaud Changes the hardware UART baud rate allowing for dynamic speed changes. Parameters BYTE NewBaud 0=1200, 1=2400, 2=4800, 3=9600, 4=19200, 5=38400, 6=57600, 7=115200 Is there a way to ...