Thanks, it really works.
I think the problem was that I set TX to 0 and RX to 1, but I had to do the opposite (TX to 1 and RX to 0).
Search found 26 matches
- Tue Jul 16, 2019 11:44 am
- Forum: E-blocks
- Topic: E-blocks 2 RFID Board (BL0197)
- Replies: 2
- Views: 5610
- Tue Jul 16, 2019 10:45 am
- Forum: E-blocks
- Topic: E-blocks 2 Actuators (BL0127)
- Replies: 1
- Views: 4733
E-blocks 2 Actuators (BL0127)
Hi, There is a difficulty with setting the Actuators (BL0127). I do not know what components to use, of those that are in Flowcode 8.2. I tried different components (attach a photo), but I could not get the result. And of course I set the port settings in accordance with the datasheet (for DC motor ...
- Mon Jul 15, 2019 4:27 pm
- Forum: E-blocks
- Topic: E-blocks 2 RFID Board (BL0197)
- Replies: 2
- Views: 5610
E-blocks 2 RFID Board (BL0197)
Hi, There is a problem with the RFID BL0197 component. This component is not initialized. The component was connected to the BL0011 Board to B and C ports. I used the RFID (EB052, RWD MICODE) component in Flowcode 8.2 and tried to set up different ports (B and C) in the connection setup. I set the T...
- Mon Jul 01, 2019 2:22 pm
- Forum: E-blocks
- Topic: E-blocks 2 Ethernet board BL0187
- Replies: 2
- Views: 5567
- Thu Jun 27, 2019 9:24 am
- Forum: E-blocks
- Topic: E-blocks 2 Ethernet board BL0187
- Replies: 2
- Views: 5567
E-blocks 2 Ethernet board BL0187
Hi,
What components can I use with the Ethernet board?
Perhaps these are components from the Network section, but I don’t know which ones can I use.
What components can I use with the Ethernet board?
Perhaps these are components from the Network section, but I don’t know which ones can I use.
- Fri Jun 07, 2019 6:17 pm
- Forum: E-blocks
- Topic: Trouble using BL0080 with mloader 4.001 same situation as danwest01
- Replies: 1
- Views: 5698
- Fri Jun 07, 2019 6:12 pm
- Forum: E-blocks
- Topic: E-blocks 2 BL0011
- Replies: 1
- Views: 5184
Re: E-blocks 2 BL0011
Okay, I solved this problem.
You need to install the necessary drivers for the board.
When you updating drivers, you must manually select them in the Flowcode v8 / Drivers folder.
This solved the problem.
P.S. Do not forget to update Flowcode to the latest version.
You need to install the necessary drivers for the board.
When you updating drivers, you must manually select them in the Flowcode v8 / Drivers folder.
This solved the problem.
P.S. Do not forget to update Flowcode to the latest version.
- Thu Jun 06, 2019 12:02 pm
- Forum: E-blocks
- Topic: E-blocks 2 BL0011
- Replies: 1
- Views: 5184
E-blocks 2 BL0011
Hello There is a problem with BL0011. After connecting via USB, Windows sees it, but mLoader (v4) does not see, and when the program is recorded on the chip, a notification appears that the device is not connected. This result is in Flowcode 8.0 and 8.2. With BL0080 and PIC16F18877 there is no such ...
- Thu Jan 17, 2019 3:35 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hi,
I checked my devices.
The program display on screen "Coordinator" for one device (with a Coordinator mark on it)
and "End device" for another (with a Router/End mark on it).
Maybe you have a program that can connect Zigbee devices?
I checked my devices.
The program display on screen "Coordinator" for one device (with a Coordinator mark on it)
and "End device" for another (with a Router/End mark on it).
Maybe you have a program that can connect Zigbee devices?
- Mon Jan 14, 2019 5:30 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hi.
Yes, I have two BL0080 boards and Zigbee Board BL0152 is connected to each of them.
I think it does not work. Can you confirm that Zigbee (eblocks 2) works in Flowcode 8?
Just send me at least one version of the program that can connect Zigbee (eblocks 2) together?
Yes, I have two BL0080 boards and Zigbee Board BL0152 is connected to each of them.
I think it does not work. Can you confirm that Zigbee (eblocks 2) works in Flowcode 8?
Just send me at least one version of the program that can connect Zigbee (eblocks 2) together?
- Wed Dec 19, 2018 10:37 am
- Forum: E-blocks
- Topic: E-blocks 2 CAN Bus (BL0140)
- Replies: 3
- Views: 6064
Re: E-blocks 2 CAN Bus (BL0140)
Hello, I have a CAN Bus Board BL0140 from Eblocks2 and a small program using CAN(Internal, MCP2515) component macros, which I took from Comms. A component is initialized in the program, and since the initialization macro does not return anything, I check in another way work it or not. After initiali...
- Wed Dec 19, 2018 10:21 am
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hello, I tried your program, it did not work.The ConnectToCoordinator marco returns zero, regardless of whether a coordinator is turn on or not, so I tried to change the loop to wait for one (instead zero). But this also does not work, so I want to try other channels, as you suggested, but I don’t q...
- Sat Dec 08, 2018 1:07 pm
- Forum: Flowcode V8
- Topic: USB in Flowcode 8
- Replies: 4
- Views: 3062
Re: USB in Flowcode 8
Hi,
Here it is.
Here it is.
- Fri Dec 07, 2018 9:18 pm
- Forum: Flowcode V8
- Topic: USB in Flowcode 8
- Replies: 4
- Views: 3062
USB in Flowcode 8
Hi,
I have a problem with creating a program using USB component from E-blocks.
I have 18F4455 chip and Flowcode 8.
I cant compile a hex-file if I have any USB component(HID, Serial, ...) in the program. Even if I don't use macros.
Could you help me with my problem?
Thanks in advance for reply.
I have a problem with creating a program using USB component from E-blocks.
I have 18F4455 chip and Flowcode 8.
I cant compile a hex-file if I have any USB component(HID, Serial, ...) in the program. Even if I don't use macros.
Could you help me with my problem?
Thanks in advance for reply.
- Fri Dec 07, 2018 8:22 am
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hi,
Here are two files that I used.
In both the same PAN ID - 1234. And Scan channels only 0x0b and 0x15.
Coordinator led blinks, End device led just stays on.
They still dont connect
Here are two files that I used.
In both the same PAN ID - 1234. And Scan channels only 0x0b and 0x15.
Coordinator led blinks, End device led just stays on.
They still dont connect
- Fri Nov 09, 2018 4:50 pm
- Forum: E-blocks
- Topic: EB to EB2 (BL0113-1)
- Replies: 1
- Views: 5176
EB to EB2 (BL0113-1)
Hello, I have a problem with connecting the Eblocks2-module to the Eblocks-board using an EB to EB2 adapter (BL0113-1). The adapter has three sockets (+V, 3V3, 5V) for wired connection, but hasn't ground socket (marked on the board as GND). I looked in the description of the BL0113 component, and th...
- Tue Oct 30, 2018 4:35 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hello,
They still dont connect together.
They still dont connect together.
- Mon Oct 22, 2018 6:32 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Hi, I tried it in different ways, but I can not connect two zigbee modules between. Can you tell me what my problem is? Below are examples of programs that should allow me to connect devices (programs dont go out of the loop where the connection occurs). I tried macros ConnectToAll, ConnectToCoordin...
- Fri Oct 19, 2018 1:22 pm
- Forum: E-blocks
- Topic: E-blocks 2 Bluetooth (BL0170)
- Replies: 6
- Views: 8004
Re: E-blocks 2 Bluetooth (BL0170)
Hello , Can I use the WaitForValue macro when connecting to a module via a mobile device or PC? I could not detect the "CONNECT" value when connected via smartphone. Therefore, I wanted to know, how can I work with the module through the PC terminal? (if its possible) Thanks in advance for the answer
- Mon Oct 08, 2018 3:31 pm
- Forum: E-blocks
- Topic: E-blocks 2 Bluetooth (BL0170)
- Replies: 6
- Views: 8004
Re: E-blocks 2 Bluetooth (BL0170)
Bluetooth module BL0170 uses Microchip RN4677 AT commands, right?
I tried various commands from here :
http://ww1.microchip.com/downloads/en/D ... 02377A.pdf
But they do not work, it may be a matter of syntax.
Could you tell me how to work with AT commands correctly?
I tried various commands from here :
http://ww1.microchip.com/downloads/en/D ... 02377A.pdf
But they do not work, it may be a matter of syntax.
Could you tell me how to work with AT commands correctly?
- Wed Oct 03, 2018 3:17 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
And here are the other two files for the same devices.
I tried to use ScanNetwork macro.
I tried to use ScanNetwork macro.
- Wed Oct 03, 2018 3:15 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Ok, there are two files - one for Zigbee Coordinator device, another for Zigbee End device.
What I tried to do, I already wrote above.
What I tried to do, I already wrote above.
- Mon Sep 24, 2018 6:53 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
Re: E-blocks 2 Zigbee (BL0152)
Thank you for considering this issue, here are some details I had a problem with connecting the end device to the coordinator. In my case, there are two circuits, each made from the PIC MultiProgrammer BL0080, Combo Board BL0114 and Zigbee Board BL0152 components. In the first one, Zigbee is a Coord...
- Wed Sep 19, 2018 10:22 am
- Forum: E-blocks
- Topic: E-blocks 2 CAN Bus (BL0140)
- Replies: 3
- Views: 6064
E-blocks 2 CAN Bus (BL0140)
Hi,
I have a problem with CAN Bus from E-blocks 2.
There is no component CAN Bus BL0140 (E-blocks2) in FlowCode 8. The macros of compo
Is it possible to release an update with this component?
Thanks in advance for your help.
I have a problem with CAN Bus from E-blocks 2.
There is no component CAN Bus BL0140 (E-blocks2) in FlowCode 8. The macros of compo
Is it possible to release an update with this component?
Thanks in advance for your help.
- Tue Sep 18, 2018 9:41 pm
- Forum: E-blocks
- Topic: E-blocks 2 Zigbee (BL0152)
- Replies: 19
- Views: 15807
E-blocks 2 Zigbee (BL0152)
Hi,
I have a problem which I hope you be able to solve.
There is no component Zigbee BL0152 (E-blocks2) in FlowCode 8. The macros of component Zigbee EB051 are not suitable.
Is it possible to release an update with this component?
Thanks in advance for your help.
I have a problem which I hope you be able to solve.
There is no component Zigbee BL0152 (E-blocks2) in FlowCode 8. The macros of component Zigbee EB051 are not suitable.
Is it possible to release an update with this component?
Thanks in advance for your help.