Benj,
Any luck replicating this fualt on your set up
Regards
Wayne
Search found 50 matches
- Wed Sep 12, 2012 10:40 am
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
- Tue Sep 11, 2012 9:32 am
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi Benj
Done a full format and still get the same result
Rgds
Wayne
Done a full format and still get the same result
Rgds
Wayne
- Mon Sep 10, 2012 4:48 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi, I have not tried a full format, What happens even when using your .wav test file is that it will play approx. 2 seconds absolutly fine then it hangs up with a hissing sound followed shortly with a sound like a stuck CD and stays like that until i reset it and it starts again then hangs up again ...
- Mon Sep 10, 2012 2:41 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
hI
Please find attached program
regards
Wayne
Please find attached program
regards
Wayne
- Sat Sep 08, 2012 10:20 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
I am now a step closer, the card was not formatted right. But the only problem now is i only get about 2 seconds of sound then it locks up and all i get is a hiss or a looped noise like a dirty cd . any ideas ?
Thanks for your help so far
Wayne
I am now a step closer, the card was not formatted right. But the only problem now is i only get about 2 seconds of sound then it locks up and all i get is a hiss or a looped noise like a dirty cd . any ideas ?
Thanks for your help so far
Wayne
- Fri Sep 07, 2012 4:46 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Its a 20 Mhz crystal (i also tried a 19.6608) on a EB006 development board and used the setting from emanuel program and also tried to adjust them but nothing seem to change ???
- Fri Sep 07, 2012 4:04 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
OK i have load a program to the 4455 ic that just prints "HI" in one second intervals to the LCD , but when loaded to the hardware it takes 20 seconds to repeat the message. i think this is the problem but how do i solve it to get the timing correct
Rgds
Wayne
OK i have load a program to the 4455 ic that just prints "HI" in one second intervals to the LCD , but when loaded to the hardware it takes 20 seconds to repeat the message. i think this is the problem but how do i solve it to get the timing correct
Rgds
Wayne
- Thu Sep 06, 2012 3:29 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
Still having problems now it will not ID the chip when compiling or clicking on auto detect. Place a 16f877 in the ic socket and it see's it no problem, changed it with a new 18f4455 and i get " Could not ID onboard chip "
Any ideas
Wayne
Still having problems now it will not ID the chip when compiling or clicking on auto detect. Place a 16f877 in the ic socket and it see's it no problem, changed it with a new 18f4455 and i get " Could not ID onboard chip "
Any ideas
Wayne
- Fri Aug 31, 2012 4:04 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
its the example program you sent me, please check chip config on my program
using EB006 Board with a 19.6608 Mhz
EB037 with jumpers on "A" and 5V and 16M MMC Card
Thanks
Wayne
its the example program you sent me, please check chip config on my program
using EB006 Board with a 19.6608 Mhz
EB037 with jumpers on "A" and 5V and 16M MMC Card
Thanks
Wayne
- Fri Aug 31, 2012 3:18 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
Still getting message LCD
Opening File
File Error: 239
Any advise
Rgds
Wayne
Still getting message LCD
Opening File
File Error: 239
Any advise
Rgds
Wayne
- Fri Aug 31, 2012 2:12 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi
What is PLL ? is it a internal clock ? and how do i change it
Thanks for your help
Rgds
Wayne
What is PLL ? is it a internal clock ? and how do i change it
Thanks for your help
Rgds
Wayne
- Fri Aug 31, 2012 12:37 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
Hi,
Can iuse a 19.6608 Crystal ? thats all i got at hand at the moment. Because at present i'm using that crystal and getting the following on the LCD
Opening file
File Error: 239
Rgds
Wayne
Can iuse a 19.6608 Crystal ? thats all i got at hand at the moment. Because at present i'm using that crystal and getting the following on the LCD
Opening file
File Error: 239
Rgds
Wayne
- Fri Aug 31, 2012 8:57 am
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
- Thu Aug 30, 2012 11:13 am
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
Re: SD e-block
I was going to use a PIC16F877/A with it's internal clock on a EB006 development board using Flowcode 4, there a limit to the size of memory card or class
- Wed Aug 29, 2012 10:47 pm
- Forum: Flowcode V4
- Topic: SD e-block
- Replies: 29
- Views: 17957
SD e-block
Hi, You show a example of playing a wav file from a sd card e-block, but can you give me some more info 1. the chip config in example is shaded out, what is the clock speed (internal,rc,xtal) 2. the sound output is on what pin (pwm) 3. what input is card reader on 4. what kind of circuit did you use...
- Wed Jan 26, 2011 8:55 am
- Forum: Flowcode V4
- Topic: RS232
- Replies: 7
- Views: 5521
Re: RS232
Good morning Benj,
What i was trying to say is on the scope from the rs232 on the pc i get the following
Null=logic 1
0xFF=logic 0
From flowcode i get
Null=logic 0
0xFF=logic 1
Which would say RS232 from flowcode is not inverted
Any idea's
Regards
Wayne
What i was trying to say is on the scope from the rs232 on the pc i get the following
Null=logic 1
0xFF=logic 0
From flowcode i get
Null=logic 0
0xFF=logic 1
Which would say RS232 from flowcode is not inverted
Any idea's
Regards
Wayne
- Tue Jan 25, 2011 3:38 pm
- Forum: Flowcode V4
- Topic: RS232
- Replies: 7
- Views: 5521
Re: RS232
Just two more question how to set up the stopbit and parity, also when i look at the data on my scope it is inverted to what i got from the pc?
Rgds
Wayne
Rgds
Wayne
- Tue Jan 25, 2011 2:29 pm
- Forum: Flowcode V4
- Topic: RS232
- Replies: 7
- Views: 5521
Re: RS232
Benj,
Am i right in saying i have to open a RS232 send macro for each of the above,i.e null then 0xff and so on
Rgds
Wayne
Am i right in saying i have to open a RS232 send macro for each of the above,i.e null then 0xff and so on
Rgds
Wayne
- Tue Jan 25, 2011 12:59 pm
- Forum: Flowcode V4
- Topic: RS232
- Replies: 7
- Views: 5521
RS232
Hi I have just captured the following RS232 data string from a pc to a message board <NUL><FF><FF><NUL><VT><SOH><FF><SOH>01<STX><EF><BO><EF<A4>TEXT<FF><FF><NUL> This was sent @ 2400buad, databits 8, stopbits 1and parity none How would i achieve this using the RS232 component in flowcode 4 Regards Wa...
- Tue Nov 25, 2008 3:10 pm
- Forum: General / Misc
- Topic: Flowcode 4
- Replies: 12
- Views: 10854
Re: Flowcode 4
is there a relaese date yet ?
Rgds
Wayne
Rgds
Wayne
- Tue Nov 25, 2008 1:12 pm
- Forum: General / Misc
- Topic: Flowcode 4
- Replies: 12
- Views: 10854
Flowcode 4
what can we look forward to in flowcode 4
Rgds
Wayne
Rgds
Wayne
- Fri Nov 21, 2008 10:23 am
- Forum: Flowcode V2 & V3
- Topic: anyone have an example for this?
- Replies: 3
- Views: 2846
Re: anyone have an example for this?
Post your program and i will have a look
Rgds
Rgds
- Wed Nov 19, 2008 3:32 pm
- Forum: Flowcode V2 & V3
- Topic: Hex to Decimal
- Replies: 17
- Views: 10643
Re: Hex to Decimal
Hi steve,
Sorry for pestering you, But how do i break down the 209 (tag) into powers of ten. I will get my head round this !
Rgds
Wayne
Sorry for pestering you, But how do i break down the 209 (tag) into powers of ten. I will get my head round this !
Rgds
Wayne
- Wed Nov 19, 2008 11:34 am
- Forum: Flowcode V2 & V3
- Topic: Hex to Decimal
- Replies: 17
- Views: 10643
Re: Hex to Decimal
Benj,
The answer to my calculation is larger than 1 byte, so what type of varible do i use. INT is ok for the first calculation, but when i get to tag2*256*256 it comes back as zero
Rgds
Wayne
The answer to my calculation is larger than 1 byte, so what type of varible do i use. INT is ok for the first calculation, but when i get to tag2*256*256 it comes back as zero
Rgds
Wayne
- Tue Nov 18, 2008 3:29 pm
- Forum: Flowcode V2 & V3
- Topic: Hex to Decimal
- Replies: 17
- Views: 10643
Re: Hex to Decimal
Is there any information on this site on how to creat a macro, so i can have a go at doing this calculation.
thanks
wayne
thanks
wayne