Search found 966 matches

by dazz
Wed Nov 19, 2014 10:16 am
Forum: Flowcode V6
Topic: It's SPI Communications active?
Replies: 11
Views: 3270

Re: It's SPI Communications active?

HI
If you buy the pro licence then all the components are fully activated

Regards
Dazz
by dazz
Sat Oct 18, 2014 2:46 pm
Forum: General Programming
Topic: Flash Memory Question
Replies: 5
Views: 2523

Re: Flash Memory Question

Hi Benj
Re Win8, win 8 doesnt defrag ssd's it doesit another way called trim only takes a few seconds to do.

Regards
DAzz
by dazz
Fri Oct 17, 2014 1:33 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

hi
i thought your fcd may have been corrupted as it appeared to point at a different programmer, have you got a link to where you bought your mega from,as if its not too expensive i may order one in a few weeks and try it here, as an aside my uno's use the ch30 drivers and work fine

Regards
Dazz
by dazz
Thu Oct 16, 2014 8:30 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi
the 2 bat files are identical to mine, can you place the attached fcd in yor avr fcd folder and try again, its a long shot but it might work
Regards
Dazz
Arduino Mega 2560.fcdx
(26.37 KiB) Downloaded 314 times
by dazz
Thu Oct 16, 2014 3:57 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi Jorgen One thing that stands out immediately is as below Mine C:\Program Files (x86)\Flowcode 6\compilers\avr\batchfiles\avrc_arduinoB.bat m2560 stk500v2 com6 115200 "Flowcode1.hex" Jorgen's C:\Program Files\Flowcode 6\compilers\avr\batchfiles\avrc_arduinoA.bat m2560 wiring com8 115200 ...
by dazz
Wed Oct 15, 2014 2:54 pm
Forum: Flowcode V5
Topic: GUIDE: Arduino programming via USB
Replies: 20
Views: 23884

Re: GUIDE: Arduino programming via USB

Hi steve
read this page, its semi automatic ;)
viewtopic.php?f=54&t=13084&start=50
Regards
Dazz
by dazz
Tue Oct 14, 2014 5:40 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi

try this see attached pic

Regards
Dazz


Untitled.jpg
Untitled.jpg (56.21 KiB) Viewed 17158 times
by dazz
Tue Oct 14, 2014 2:01 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi
It should be automatic, but i have to reset my mega before it programs, wsee attached pic, when it gets to that point hold the mega reset buton and release it as soon as you press ok

Regards
Dazz

Untitled1.jpg
Untitled1.jpg (48.32 KiB) Viewed 17162 times
by dazz
Tue Oct 14, 2014 12:52 pm
Forum: General Programming
Topic: fc v6 pic error code 255
Replies: 5
Views: 3036

Re: fc v6 pic error code 255

Hi Kon

Have a look in the avast virus vault, as on my laptop it stopped compiling, because avast was trying to be clever. if its in there click on restore and add to exeptions(something like that)

Regards
DAzz
by dazz
Tue Oct 14, 2014 12:49 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi
i can program mine but i have to reset it just before it times out, i think it may need a reset putting into the parammeters, how i dont know :)
try clicking build and you can select the arduino in a box on the right make sure it corresponds with the port you are using and try again#

Regards
Dazz
by dazz
Tue Oct 14, 2014 10:22 am
Forum: Feature requests
Topic: EB088 support
Replies: 1
Views: 1255

EB088 support

Hi Guys
Any chance of a component for the EB088 Eblock cap touch board

Regards
Dazz
by dazz
Tue Oct 14, 2014 10:16 am
Forum: Flowcode V6
Topic: PICKIT 2
Replies: 4
Views: 1670

Re: PICKIT 2

HI Fella
try updating the firmware in the pickit2, as you may have different file versions, i had to do this a while back

Regards
Dazz
by dazz
Mon Oct 13, 2014 2:24 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi Monie
select the default programmer in V6.1 set it to default and try again, also when you uninstalled did you also remove the flowcode folder on your c drive as this will keep the old compiler settings etc

Regards
Dazz
by dazz
Sun Oct 12, 2014 5:48 pm
Forum: Flowcode V6
Topic: Interrupt Arduino Uno
Replies: 16
Views: 4528

Re: Interrupt Arduino Uno

Hi jorgen

i got my sums wrong it should have been 31250 i think, was tired yesterdat sorry

Regards
Dazz
by dazz
Sun Oct 12, 2014 5:46 pm
Forum: Flowcode V6
Topic: Arduino Programming In Flowcode v6
Replies: 115
Views: 114146

Re: Arduino Programming In Flowcode v6

Hi Monie
works here, try this click on build and there should be a drop down box called programmer port select your port then compile to chip,

Regards
Dazz


Flowcode1.msg.txt
(3.42 KiB) Downloaded 331 times
by dazz
Sun Oct 12, 2014 12:31 pm
Forum: Flowcode V6
Topic: adc voltage sample program
Replies: 13
Views: 4598

Re: adc voltage sample program

Hi
ran your chart and had the following results, are you using V6.1 as i think other versions had an adc issue on the arduino 2560. if not download v6.1 and try again
Regards
Dazz

check1.jpg
(221.84 KiB) Downloaded 1190 times


check2.jpg
(126.08 KiB) Downloaded 1190 times


check3.jpg
(125.43 KiB) Downloaded 1190 times
by dazz
Sun Oct 12, 2014 12:12 pm
Forum: Flowcode V6
Topic: Interrupt Arduino Uno
Replies: 16
Views: 4528

Re: Interrupt Arduino Uno

Hi
All i know is if you place a delay in an interupt it will cause issues like you are getting, which is why its better to use a count like in the chart i did,

hope that helps

Regards
Dazz
by dazz
Sat Oct 11, 2014 8:32 pm
Forum: Flowcode V6
Topic: adc voltage sample program
Replies: 13
Views: 4598

Re: adc voltage sample program

Hi

Run the sim and dragf the speed slider to the right a bit this will then show all the variables, by doing this tension was displaying

Regards
Dazz
by dazz
Sat Oct 11, 2014 8:10 pm
Forum: Flowcode V6
Topic: ECIO40P16 compile errors and a ton of warnings
Replies: 13
Views: 3170

Re: ECIO40P16 compile errors and a ton of warnings

Hi Fella
Can you post your flowchart as it may allow someone to spot the error
Regards
Dazz
by dazz
Sat Oct 11, 2014 8:08 pm
Forum: Flowcode V6
Topic: Interrupt Arduino Uno
Replies: 16
Views: 4528

Re: Interrupt Arduino Uno

Hi
Try the attached chart, basically at 16mhz a count of 31(ish) will = 1/2 sec , so one int triggered ,it counts switches on led and off at end of copunt, its not the tidiest chart but try it and let us know if it works for you

Regards
Dazz


Smeden try this.fcfx
(7.94 KiB) Downloaded 119 times
by dazz
Fri Oct 10, 2014 5:43 pm
Forum: General Programming
Topic: New(edit) Component
Replies: 12
Views: 7612

Re: New(edit) Component

hi
the macros you dont use are removed during compiling

Regards
Dazz
by dazz
Fri Oct 10, 2014 2:12 pm
Forum: General Programming
Topic: Flowcode V5 -> V6
Replies: 9
Views: 4454

Re: Flowcode V5 -> V6

Hi

Will this open on your V6
Regards
Dazz

Key Pad Coding-1.fcfx
(23.95 KiB) Downloaded 121 times
by dazz
Thu Oct 09, 2014 5:37 pm
Forum: Flowcode V6
Topic: re: Flowcode purchase
Replies: 6
Views: 2628

Re: re: Flowcode purchase

Hi
Email the lady who sent the email and see the reasons you need to pay vat,

Regards
Dazz
by dazz
Thu Oct 09, 2014 12:18 pm
Forum: Flowcode V6
Topic: Flowcode V6 Ic2
Replies: 5
Views: 2026

Re: Flowcode V6 Ic2

HI
What i do is import it into V6, then i simply replace the components with the V6 ones

Regards
Dazz
by dazz
Thu Oct 09, 2014 12:17 pm
Forum: Flowcode V6
Topic: Flowcode 6.1 Released!
Replies: 46
Views: 37603

Re: Flowcode 6.1 Released!

Hi Martin
:oops: :oops: :oops: :oops: YOu are correct i've just updated ,i was basing it on the beta :lol:

Regards
Dazz