Search found 87 matches

by kennethnilsen69
Tue Dec 15, 2015 5:09 pm
Forum: E-blocks
Topic: Is my gsm EB066 card defective?
Replies: 10
Views: 8223

Re: Is my gsm EB066 card defective?

Hi Benj yes I use pin 0 and 1 as UART port and which are still connected to the bootloader. is this a problem even if I am not connected with USB port? my Prog/Port switch on the E-block adapter is in RUN position, which is to be the correct position. I have checked this with my multimeter. In GSM p...
by kennethnilsen69
Tue Dec 15, 2015 1:57 pm
Forum: E-blocks
Topic: Is my gsm EB066 card defective?
Replies: 10
Views: 8223

Re: Is my gsm EB066 card defective?

Thank you for your input Peter but my RS232 port is functioning properly and I can log it from my pc. my arduino stops when it tries to initialize the GSM board. it sends the command AT+CMGF=1 over and over again. No response from GSM board. but what about this? When I connect 14 volts to VPWH, 5 vo...
by kennethnilsen69
Tue Dec 15, 2015 12:51 am
Forum: E-blocks
Topic: Is my gsm EB066 card defective?
Replies: 10
Views: 8223

Is my gsm EB066 card defective?

Hi just received my new GSM E-Block and I can not get no life in it My setup is 1. Arduino UNO 1. E-blocks Arduino Uno Shield EB093 1. E-blocks GSM board EB066 1. Vellerman 0-30V 0-5A 1. LCD 2004 20x4 I2C bus Fowcode v6 I've set it up in Patch config and I use this test file that is adapted to my se...
by kennethnilsen69
Mon Nov 09, 2015 7:31 am
Forum: Flowcode V6
Topic: 4D system display uLCD-43PT-AR or uLCD-43DT-AR
Replies: 3
Views: 1317

Re: 4D system display uLCD-43PT-AR or uLCD-43DT-AR

fantastic Stuart :-) now I can order a display :-)

Thanks
Kenneth
by kennethnilsen69
Sun Nov 08, 2015 10:52 am
Forum: Flowcode V6
Topic: 4D system display uLCD-43PT-AR or uLCD-43DT-AR
Replies: 3
Views: 1317

4D system display uLCD-43PT-AR or uLCD-43DT-AR

Is there component suport for 4.3 inch displays from 4D system in flovcode 6?
I see that there is component to uLCD-32PTU. but for my project but I think it's a little small display and I'd rather have 4.3 inch displays :-)
or can I possibly use uLCD-32PTU component to uLCD-43 displays?
by kennethnilsen69
Wed Sep 09, 2015 5:01 pm
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using LCD i2c
Replies: 3
Views: 2215

Re: Arduino Software and FlowCode difference using LCD i2c

it is fantastic Ben :-) this worked very well :-)))).

Thanks so much Ben :-)
by kennethnilsen69
Wed Sep 09, 2015 12:32 pm
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using LCD i2c
Replies: 3
Views: 2215

Arduino Software and FlowCode difference using LCD i2c

Hi I need some help regarding slow i2c bus in FlowCode using a 4x20 LCD. When I programerer with Arduino then i2c lcd is quick and ok but with Flowcode it becomes so slow I have this i2c: http://www.ebay.com/itm/310565362720?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT and this lcd...
by kennethnilsen69
Tue Sep 08, 2015 1:58 pm
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using CanBus-shield
Replies: 11
Views: 3365

Re: Arduino Software and FlowCode difference using CanBus-sh

// Set CAN bit time segments // SyncSeg = 1, PropSeg = 2, PhaseSeg1 = 2, PhaseSeg2 = 3 // Total bits = 8 @ 16MHz/4 gives CAN Bit Time for 500kbs FC_CAN_SPI_CAN_Config_1(128); // put MCP2515 into CONFIG mode FC_CAN_SPI_CAN_Write_1(42, 0x01); // set CNF1 register to 0b00000001 FC_CAN_SPI_CAN_Write_1(...
by kennethnilsen69
Mon Sep 07, 2015 5:15 pm
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using CanBus-shield
Replies: 11
Views: 3365

Re: Arduino Software and FlowCode difference using CanBus-sh

Try this inside a C icon placed just after the can::Initialise call. FC_CAN_SPI_CAN_Config_1(128); FC_CAN_SPI_CAN_Write_1(42, 0x01); FC_CAN_SPI_CAN_Write_1(41, 0xc9); FC_CAN_SPI_CAN_Write_1(40, 0x02); FC_CAN_SPI_CAN_Config_1(0); this is fantastic :-) this did the trick. :-))) Now everything works a...
by kennethnilsen69
Mon Sep 07, 2015 10:12 am
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using CanBus-shield
Replies: 11
Views: 3365

Re: Arduino Software and FlowCode difference using CanBus-sh

You also might need to check the Tx ID. Your Flowcode component is set to "Standard Only" you might need "Extended", as your ID seems to be outside the Standard range? Also the SetTxID(0,100,0) macro expects the ID in MCP2515 register format, you probably need to use SetTxIdent(...
by kennethnilsen69
Mon Sep 07, 2015 9:28 am
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using CanBus-shield
Replies: 11
Views: 3365

Re: Arduino Software and FlowCode difference using CanBus-sh

Have you checked the baudrate? (Or does the analyzer automatically determine the speed?) With two Flowcode programs the baudrate will match even if the setting does not reflect the required baudrate but other components using the correct speed will not see any data. Yes I have, they all have the sa...
by kennethnilsen69
Sun Sep 06, 2015 3:56 pm
Forum: Flowcode V6
Topic: Arduino Software and FlowCode difference using CanBus-shield
Replies: 11
Views: 3365

Arduino Software and FlowCode difference using CanBus-shield

Hi I have a little trouble with understanding the difference between Arduino software and FlowCode using CAN component. I've created two identical CAN send applications. 1 in FlowCode and 1 in Arduino software. I connect my Arduino to my computer with ixxat CAN-To-USB interface and monitors traffic ...