Search found 300 matches

by AbhijitR
Wed Oct 12, 2022 3:11 pm
Forum: Flowcode V8
Topic: Change UART Properties
Replies: 4
Views: 11910

Re: Change UART Properties

Hello! Ben
Good afternoon

Many many thanks for the reply/answer, I shall try your suggestions after I reach home, I am sure that will work,.

Thank you again.

Abhi
by AbhijitR
Tue Oct 11, 2022 12:35 pm
Forum: Flowcode V8
Topic: Change UART Properties
Replies: 4
Views: 11910

Change UART Properties

Hello! I am using the MODBUS Slave component, the PIC chip is 18F26K42 running @16Mhz, everything is working good for the moment when communicating with MODSCAN32 or RADZIO on computer, but i am facing problem while communicating with some other hardware or other computer software which is demanding...
by AbhijitR
Tue Sep 27, 2022 10:21 am
Forum: Flowcode V8
Topic: RFID RC-522
Replies: 0
Views: 38514

RFID RC-522

Hello! Since yesterday I am trying to make my RC-522 work with PIC18F26K22, I used the chart from the below link shared by Ben. https://www.matrixtsl.com/wiki/index.php?title=Component:_ID_3f8d29a6_40a6_4d5e_a254_190c86d9ebb7 One of the changes I made in this chart is the controller, as I do not use...
by AbhijitR
Thu Jul 07, 2022 4:08 pm
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hi! Chipfryer good evening Kindly excuse for the silence on the project, i am traveling to north of India to complete the LoRa project, probably will finish in next week, i hope :D, site work always take time to finish as customer always has something to modify till the last moment :evil:. I've been...
by AbhijitR
Sun Jun 12, 2022 7:25 pm
Forum: Flowcode V8
Topic: RPI and long distance radio
Replies: 27
Views: 15268

Re: RPI and long distance radio

Hello! Chipfryer27 Good evening my friend As said I finished the LoRa GAMMA project, I am sharing few pictures, apart from transmitter and receiver I have also added one transreceiver to make sure the signal reach till the end as transmitter and receiver are not in line of sight. No doubt the applic...
by AbhijitR
Thu Jun 09, 2022 7:01 am
Forum: Flowcode V8
Topic: MODBUS Slave
Replies: 12
Views: 9786

Re: MODBUS Slave

Hello! Ben good morning Following your last post regarding the update about few settings for UART, may i request you to please help me solve this problem. Hello, My take on this is it should be possible but it would certainly be a software addition to the CAL UART where we increase the data bits fro...
by AbhijitR
Sun May 29, 2022 5:24 am
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hello! Viktor Good morning Yes you are absolutely right, I am busy for the moment finishing one of the projects using LoRa (GAMMA) and for your surprise it is Chipfryer27 who educated me about using that module, I will share the pictures of that project once ready, probably in the beginning of next ...
by AbhijitR
Mon May 16, 2022 5:39 pm
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hello! Chipfryer27 good evening Precise answers, you are too good while answering the doubts. Regarding the data collection and process, i think it is too early for me, as a beginner i shall first try to display the data on the webpage, if this task is achieved then i shall take the next step of sto...
by AbhijitR
Wed May 11, 2022 5:10 pm
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hello! Chipfryer27

Your time is my time my friend, i wait eagerly for your post, by the time i will read as much as possible on internet.

Thank you again.

Regards
Abhi
by AbhijitR
Tue May 10, 2022 10:13 am
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hello! Chipfryer27 good morning Thanks for your post, now the ball is in my court, :) I want to transmit analog value of one of the sensor which will indicate the level of water. As far as i know after reading few datasheets there are 3 different type of transmission modes SMS, Email and FTP, right?...
by AbhijitR
Tue May 10, 2022 6:07 am
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Re: Send Data on email using GPRS

Hello! Viktor Good afternoon Many thanks for your reply. I have 2 modules, one is SIM800A and another one is SIM800L EVB, mentioned as V2, to be honest I am not aware why mentioned as V2 for this module, probably some more functions are available. When I purchased this modules in the past I thought ...
by AbhijitR
Mon May 09, 2022 12:40 pm
Forum: Flowcode V8
Topic: Send Data on email using GPRS
Replies: 60
Views: 36134

Send Data on email using GPRS

Hello! good afternoon May i request to help me understand or suggest a starting point, i want to work on a project where i can transmit data (it could be status of any sensor or any analog value) using data connection from SIM card or mobile service provider. I want to transmit data to some email ad...
by AbhijitR
Tue Jan 18, 2022 9:39 am
Forum: Flowcode V8
Topic: MODBUS Slave Holding Registers
Replies: 2
Views: 1931

MODBUS Slave Holding Registers

Hello! I am working on MODBUS Slave and i noticed one problem (i am not sure if this is a problem or it is like that only), when i assign SetHoldingRegister or ReadHoldingRegister in a sequence all goes well till i assign Coil Address 00007, when i assign Coil Address 00008 and 00009 then the warnin...
by AbhijitR
Sat Dec 25, 2021 9:48 am
Forum: Flowcode V8
Topic: Merry Christmas
Replies: 1
Views: 1401

Merry Christmas

Hello!

Wish you all a Merry Christmas.

Regards
Abhi
by AbhijitR
Thu Dec 23, 2021 9:02 am
Forum: Flowcode V8
Topic: Add new chip in the list
Replies: 0
Views: 37904

Add new chip in the list

Hello! Matrix Team good morning May i request you to add one of the below mentioned chips in the 8Bit list, this is one of the chips available and i was thinking to use this in my next project as the one i was using before is not available for next 11 months. PIC18LF26K83 I will be glad if this chip...
by AbhijitR
Thu Dec 09, 2021 7:44 pm
Forum: Flowcode V8
Topic: SDI/MISO pin in DAC application
Replies: 2
Views: 1675

Re: SDI/MISO pin in DAC application

Hello! Bachman
Good evening

Thank you for the answer, it would be a good news if I could use that pin as output, but unfortunately not. Now I need to think of some other option.

Thank you again for your time.

Abhi
by AbhijitR
Thu Dec 09, 2021 2:02 pm
Forum: Flowcode V8
Topic: SDI/MISO pin in DAC application
Replies: 2
Views: 1675

SDI/MISO pin in DAC application

Hello! good evening I am using MCP4921 DAC, communicating with PIC on SPI, one of the connections mentioned in the properties window is SDI/MISO (pin C4 in channel 1 of chip PIC18F26K22), may i know if it is possible to use this pin for other application as it is not connected or not used as no data...
by AbhijitR
Sun Dec 05, 2021 5:43 pm
Forum: Flowcode V7
Topic: Variable watch/modify window in FC7
Replies: 5
Views: 3484

Re: Variable watch/modify window in FC7

Hi! Martin
good evening

You indeed are Wikipedia for FlowCode, cheers...

Abhi
by AbhijitR
Mon Nov 08, 2021 8:07 am
Forum: Flowcode V8
Topic: ADC NOISE REDUCTION in AVR
Replies: 10
Views: 4058

Re: ADC NOISE REDUCTION in AVR

Hello! Is it possible to know what is the type of analog signal you are trying to sense from the field, is it some kind of current transmitter (4-20mA) or any other type and how do you convert that signal to feed to the microcontroller, is there some analog circuit in between to stabilize the signal...
by AbhijitR
Thu Nov 04, 2021 3:28 pm
Forum: 8-Bit PIC
Topic: FAT SD Card Data Logger
Replies: 28
Views: 34563

Re: FAT SD Card Data Logger

Hello! Georg good evening A small input from me if it is of any help, i used your chart (FAT_Data_Logger_Simple_Slow.fcfx) from second post and it really worked good for me, no doubt i did few modifications about the execution of the steps without any problem, yes one thing is for sure need to follo...
by AbhijitR
Thu Oct 21, 2021 7:24 am
Forum: General Programming
Topic: Storing long negative numbers in EEPROM
Replies: 15
Views: 11815

Re: Storing long negative numbers in EEPROM

Hello! Martin good morning Yes, Ben has worked on almost every probable doubt and question one can have, thank you to everyone to make Flowcode a wonderful option to program micro, someone like me was helpless few years back when i did not had Flowcode and "C" was not my cup of tea. Cheers to the th...
by AbhijitR
Wed Oct 20, 2021 5:07 pm
Forum: General Programming
Topic: Storing long negative numbers in EEPROM
Replies: 15
Views: 11815

Re: Storing long negative numbers in EEPROM

Hello! Martin good evening Your trick worked like a piece of cake, million thanks again, as usual SAVIOUR. For knowledge one of the warnings after compiling the chart disappeared, it was as below Total_16BADC_SDC_RTC_OLED_20-10-2021.c: 16714: (753) undefined shift (16 bits) (warning) Total_16BADC_SD...
by AbhijitR
Wed Oct 20, 2021 11:31 am
Forum: General Programming
Topic: Storing long negative numbers in EEPROM
Replies: 15
Views: 11815

Re: Storing long negative numbers in EEPROM

Hello! Martin good morning Thank you for your reply, i am trying to use exactly the same like Ben has mentioned in his post, attached is the chart for your reference. I would like to mention one thing this works very well in simulation but when i run this at actual then i saw the mistake of displayi...
by AbhijitR
Wed Oct 20, 2021 10:08 am
Forum: General Programming
Topic: Storing long negative numbers in EEPROM
Replies: 15
Views: 11815

Re: Storing long negative numbers in EEPROM

Hello! Ben good morning You can do this using calculations. Here I have 4 byte variables and a long variable. byte0 = long & 0xFF byte1 = (long >> 8 ) & 0xFF byte2 = (long >> 16) & 0xFF byte3 = (long >> 24) & 0xFF You can now save your bytes to EEPROM. To get back from bytes to a long you reverse th...
by AbhijitR
Tue Oct 12, 2021 1:00 pm
Forum: Flowcode V8
Topic: Script Syntax Error
Replies: 6
Views: 3324

Re: Script Syntax Error

Hello! Steve
good afternoon

The Script Error pops every time i try to save the project, i read above post so not worried just want to put to notice.

Abhi