Matrix user forums

Thanks for your help Leigh it works as it should now ))

Hi I needs some help to GSM sendTextMessage component I have an SMS I will send from string variables for example var1 [20] = Hello I am Trying var2 [20] = To send a SMS var3 [20] = true Variable var4 [20] = but I can not var5 [20] = send morethan var6 [20] = 28 characters SMS_str [100] If I send it...

Hi I have a sim808 module that has only one UART port. one sim808 has GSM, GPS and BT as all communicating via same UART port. And here comes my problem. When I set GSM and GPS components to the same port then I get an error message when it shall compile to hex file. Is this not possible in flowcode...

MPLAB 8_92 is now installed and the driver set to it. with my pickit3 then I get now this message Connecting... PICkit 3 detected Connecting to PICkit 3... Running self test... Self test completed Firmware Suite Version...... 01.40.13 Firmware type......................PIC18F .. PICkit 3 Connected. ...

I have today only MPLABX installed. I'll install MPLAB 8_92 tonight and we'll see if that helps
Thanks

As the headline says so I do not get any of them to work in flowcode. I have tested them both in MPLABX IDE and here works them properly. I can make the program in flowcode and upload the hex file with MPLABX but it is little inconvenient way of working I've tried everything in this post but this wi...

Thank you and I have now upgraded my FlowCode to include also the PIC chip Pack

Hey, there is support for PIC18F2685 in flowcode. if not can you make it?

Benj wrote:Hello,

No I'm afraid that Flowcode does not currently support the chip used on that platform. Looks interesting though.

What does it take for you to add this chip? can it be done?

Benj wrote:Hello,

Can I ask why we can not choose software channel in the GSM component?

The component uses receive interrupts to increase the reliability of the code. This is why software mode is not currently available as an option.

Will this ever be available? I definitely hope this will come

it is possible to use Opentracker? with flowcode_v6
https://geolink.io/opentracker.php

and with some googling I found out that error message means CMS ERROR: 311 SIM PIN required Hmm so I removed the sim code and valla I am now on the the GSM network and everything works as it should :-)))))))))))) But if you have time so I really appreciate if you could find a solution so that I can ...

Hey Benj it's ok :-) I have the whole day working on and it suddenly began pulling little more current. It now draws 0.18A which I imagine is a bit more normal. I the gsm chip also now gets a little hot. but could not get it to work anyway. it now gives 2.8 volts to SIM card so something is begining...

Here is a youtube video showing that I only get a very short blink of the LED when I put 14V on. https://www.youtube.com/watch?v=Kb4RCNhLEOg I do not know but this does not seem right to me. Here are some pictures https://dl.dropboxusercontent.com/u/20952570/Flowcode/Problem/GSM/20151215_230600.jpg ...

Hi Benj yes I use pin 0 and 1 as UART port and which are still connected to the bootloader. is this a problem even if I am not connected with USB port? my Prog/Port switch on the E-block adapter is in RUN position, which is to be the correct position. I have checked this with my multimeter. In GSM p...

Thank you for your input Peter but my RS232 port is functioning properly and I can log it from my pc. my arduino stops when it tries to initialize the GSM board. it sends the command AT+CMGF=1 over and over again. No response from GSM board. but what about this? When I connect 14 volts to VPWH, 5 vo...

Hi just received my new GSM E-Block and I can not get no life in it My setup is 1. Arduino UNO 1. E-blocks Arduino Uno Shield EB093 1. E-blocks GSM board EB066 1. Vellerman 0-30V 0-5A 1. LCD 2004 20x4 I2C bus Fowcode v6 I've set it up in Patch config and I use this test file that is adapted to my se...

fantastic Stuart now I can order a display

Thanks
Kenneth

Is there component suport for 4.3 inch displays from 4D system in flovcode 6?
I see that there is component to uLCD-32PTU. but for my project but I think it's a little small display and I'd rather have 4.3 inch displays
or can I possibly use uLCD-32PTU component to uLCD-43 displays?

it is fantastic Ben this worked very well ))).

Thanks so much Ben

Hi I need some help regarding slow i2c bus in FlowCode using a 4x20 LCD. When I programerer with Arduino then i2c lcd is quick and ok but with Flowcode it becomes so slow I have this i2c: http://www.ebay.com/itm/310565362720?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT and this lcd htt...

// Set CAN bit time segments // SyncSeg = 1, PropSeg = 2, PhaseSeg1 = 2, PhaseSeg2 = 3 // Total bits = 8 @ 16MHz/4 gives CAN Bit Time for 500kbs FC_CAN_SPI_CAN_Config_1(128); // put MCP2515 into CONFIG mode FC_CAN_SPI_CAN_Write_1(42, 0x01); // set CNF1 register to 0b00000001 FC_CAN_SPI_CAN_Write_1(...

Try this inside a C icon placed just after the can::Initialise call. FC_CAN_SPI_CAN_Config_1(128); FC_CAN_SPI_CAN_Write_1(42, 0x01); FC_CAN_SPI_CAN_Write_1(41, 0xc9); FC_CAN_SPI_CAN_Write_1(40, 0x02); FC_CAN_SPI_CAN_Config_1(0); this is fantastic :-) this did the trick. :-))) Now everything works a...

You also might need to check the Tx ID. Your Flowcode component is set to "Standard Only" you might need "Extended", as your ID seems to be outside the Standard range? Also the SetTxID(0,100,0) macro expects the ID in MCP2515 register format, you probably need to use SetTxIdent() macro Another issu...

Have you checked the baudrate? (Or does the analyzer automatically determine the speed?) With two Flowcode programs the baudrate will match even if the setting does not reflect the required baudrate but other components using the correct speed will not see any data. Yes I have, they all have the sa...