Search found 64 matches
- Mon Jan 27, 2020 1:03 am
- Forum: Bug Reports
- Topic: 24C16 component - Resolved
- Replies: 5
- Views: 3182
Re: 24C16 component - NOT FUNCTIONING??
Hello Leigh... YES OF COURSE... Sir... That is absolutely correct.....!! I thank you very much for pointing this out to me...??? Silly me... I just overlooked that completely....!! So ... now - are you folks... gonna construct further sized components... for like 24C64 ... and say 24C256...??? in th...
- Mon Jan 27, 2020 12:44 am
- Forum: Bug Reports
- Topic: MCP7940 - scrambling a preset clock time - Resolved
- Replies: 11
- Views: 6248
MCP7940 - scrambling a preset clock time - Resolved
Hello folks... good early morning to you all... Okay so I spent some time constructing a typical MCP7940 clock circuit on a small PCB... along with a 3V cell... for battery backup... with plainly 5 pins which simply plug into a white breadboard.. The pins are - 5V ... and GND (0V).. then SDA... SCL....
- Fri Jan 24, 2020 7:43 am
- Forum: Bug Reports
- Topic: 24C16 component - Resolved
- Replies: 5
- Views: 3182
Re: 24C16 component - NOT FUNCTIONING??
Hello Leigh... REALLY... I did not know that.... The datasheets I have from ST... show that they are like "really" identical... (excepting for the size..)??? So I expected that the 24C16 component.. should just work on the 24C32... BUT only address a max of 16K... odd...??? Leigh - I ALWAYS WANT TO ...
- Fri Jan 24, 2020 7:34 am
- Forum: Bug Reports
- Topic: UART - software mode - Resolved
- Replies: 6
- Views: 3279
Re: UART - software mode....????? what is the SECRET???
Hello guys.... yeah - just to report that I took the hardware option first.. I scratched around the PIC box... and found a "newer" PIC 16F1824... set it to 16000000 Hz... and just changed the options... and so now am very thankful to announce that... at 16000000 Hz... the SOFTWARE option - of the UA...
- Fri Jan 24, 2020 5:33 am
- Forum: Bug Reports
- Topic: UART - software mode - Resolved
- Replies: 6
- Views: 3279
Re: UART - software mode....????? what is the SECRET???
Hello Ben.. and Martin... and others... GEE - thanks for this. I will TRY ALL suggested, and see what happens.. maybe Martin ..( mnf).. could have a peek at this, and see .. I believe he is a real experimental GURU. I am using the version 1.45 of the XC8 in PRO MODE. If I have to upgrade, well then ...
- Thu Jan 23, 2020 6:55 am
- Forum: Bug Reports
- Topic: UART - software mode - Resolved
- Replies: 6
- Views: 3279
UART - software mode - Resolved
Hello --- so now I have a PIC16F688 running on internal clock at 8000000 Hz... The hardware channel for the UART... is RC4 and RC5 ... So when you connect a small circuit of RS232 chip and components to them and program a small program into the '688... you get a very good output..!! However - when y...
- Wed Jan 22, 2020 6:09 am
- Forum: Bug Reports
- Topic: 24C16 component - Resolved
- Replies: 5
- Views: 3182
24C16 component - Resolved
Hello folks... I have attached a flowchart - I used for 24C32.. which eventually I got working on 24C32.. Having done this.. datasheets shows me, that 24C16 should work just as well... with no hardware changes.. So I changed to 24C16... component... and unfortunately the program has stopped working....
- Tue Jan 21, 2020 10:33 pm
- Forum: Bug Reports
- Topic: Connection Points Bug - Resolved
- Replies: 7
- Views: 4064
Re: Connection Points Bug - and EEPROM writing..
Hello folks... OKAY - SO I AM the STUPID..!!!! Whilst I wrote the little EEPROM writing program... I got up to a point in the program... when after... I forgot to edit in the loop reset instruction... So after about index pointer... I forgot to ADD a calculation box.. and add in... variable reset in...
- Sat Jan 18, 2020 6:53 am
- Forum: Bug Reports
- Topic: Bad mistake in FC8!
- Replies: 48
- Views: 41253
Re: Bad mistake in FC8!
Hello Christina.... okay so now .. what type of processor do you have in your PC..??? apparently.. some versions of certain processors... had faults "built into the die"... I would suggest that you try to find ..."an oldish" INTEL core ... whatever you can... and try that...??? If you using an AMD.....
- Fri Jan 17, 2020 7:25 am
- Forum: Bug Reports
- Topic: Connection Points Bug - Resolved
- Replies: 7
- Views: 4064
Re: Connection Points Bug
Hello guys... okay so at 3 am... I even tried the 24C16 component... hmmm... even worse...!!.. so 24C16 component is also "broken"... Also when you "download" the 24C16 icon to say the 2D dashboard panel.. it reports itself as a 32K EEPROM... surely this should rather be... 16K EEPROM..???? (another...
- Fri Jan 17, 2020 1:42 am
- Forum: Bug Reports
- Topic: Connection Points Bug - Resolved
- Replies: 7
- Views: 4064
Re: Connection Points Bug
Hello Benj... and Hello Steve.... So I did a bit of 'digging'... (not inside FC... ) but after some logical thinking... and I found something real interesting...!!!.. So just go create a flowchart like the following... Make up a program... use build function to set a processor like PIC16F1936... run...
- Wed Jan 15, 2020 1:42 pm
- Forum: Bug Reports
- Topic: Connection Points Bug - Resolved
- Replies: 7
- Views: 4064
Connection Points Bug - Resolved
Hello guys... please can you fix this soonest - it is stopping my further development..!!! using the JUMP to icons... you can create all A -> Z... okay... Then try to create another JUMP to - it claims to be AA:AA ... and when you try to program the JUMP FROM ... icon...to AA:AA ... it doth not acce...
- Sun Jan 12, 2020 10:39 am
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
Re: PIC16F1936 software set UART... NOT correct.
Hello Folks.... DCW here again...!!! OKAY - SO I WAS THE STUPID ONE..!!!! I spent some time looking at the chip that MICROCHIP made so beautifully for us...!!!! BRILLIANT PIECE OF ENGINEERING.!!!! So it has a range of frequencies it can work on.... so I selected 4000000 Hz... to begin with..... hmmm...
- Sun Jan 12, 2020 8:32 am
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
Re: PIC16F1936 software set UART... NOT correct.
Hello guys.... you got a greater problem - than you expect... It seems none of you can READ the post correctly...??? Where the HELL - did I state - 40 mHz...??? GO ON TELL ME PLEASE..???... GO ON PLEASE SHOW ME..!!!! It seems very obvious to me - that NONE of you guys have tried - WHAT I HAVE tried....
- Mon Jan 06, 2020 8:17 pm
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
Re: PIC16F1936 software set UART... NOT correct.
Hello Ben... can you not rewrite the routines of FLOWCODE... so that they work correctly....???? you should by rights... do this...!! please..???
- Sun Jan 05, 2020 6:48 pm
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
Re: PIC16F1936 software set UART... NOT correct.
WE NOT OUT THE WOODS YET...????? GREATER TROUBLES AHEAD... PLEASE READ BELOW... Okay guys so I have a simple circuit... utilizing a PIC16F1936... 28 pin ..as I have posted in the above posts... So I have used the UART in hardware, on Tx and Rx, on the chip... and because I need a simple RS232 output...
- Tue Nov 26, 2019 10:25 am
- Forum: Bug Reports
- Topic: C-code icon.. does not stop ..!!! (1)
- Replies: 7
- Views: 3618
Re: C-code icon.. does not stop ..!!! (1)
As USUAL a BUG of this type is not attacked by the authors of flowcode... because they know about it... I am sure....!!! and will make you PAY for a fix of it.... in the next version.. of flowcode...!!! So ...the story goes...!!!!... on and on....!! there is a saying... "warts 'n all".... in flowcod...
- Sun Nov 24, 2019 4:49 pm
- Forum: Bug Reports
- Topic: C-code icon.. does not stop ..!!! (1)
- Replies: 7
- Views: 3618
Re: C-code icon.. does not stop ..!!! (3)
this is part 3... of the message ... where I needed to post screenshots of program and errors...
- Sun Nov 24, 2019 4:48 pm
- Forum: Bug Reports
- Topic: C-code icon.. does not stop ..!!! (1)
- Replies: 7
- Views: 3618
Re: C-code icon.. does not stop ..!!! (2)
this is message 2 part ... containing 3 more screenshots...
- Sun Nov 24, 2019 4:46 pm
- Forum: Bug Reports
- Topic: C-code icon.. does not stop ..!!! (1)
- Replies: 7
- Views: 3618
C-code icon.. does not stop ..!!! (1)
Hello there ... so I was attempting to test some program that I wanted to transmogrify... from mikroC PRO compiler... C - coding... into flowcode8.. and came across something really peculiar...!! So I have attached some PNG screenshots of flowcode program, and then the compiler errors it produces......
- Mon Nov 18, 2019 7:12 pm
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
Re: PIC16F1936 software set UART... NOT correct.
Hello peeps... and anyone... and someone... So the problem - I sorted out...! I forgot that I was working with BAUD RATES ... which are special ... OLD FASHONED time .. frequencies... So the solution is to set the microprocessor crystal "speed" to this number... OR a multiple of it... 3276800 Hz... ...
- Mon Nov 18, 2019 5:11 pm
- Forum: Bug Reports
- Topic: PIC16F1936 software set UART... NOT correct.
- Replies: 10
- Views: 5415
PIC16F1936 software set UART... NOT correct.
Hello anyone.. and someone .. this is a small problem with a SOFTWARE setup UART port. I using the built in TX/RX .. C6/C7 for another communication. BUT.. I need to have another TX port to help / aid.. in operation of the project... so I took RB4.. and 'turned' it into a TX port, using the SOFTWARE...
- Mon Nov 18, 2019 4:49 pm
- Forum: Flowcode V8
- Topic: Pure Sine Wave Inverter
- Replies: 38
- Views: 39937
Re: Pure Sine Wave Inverter
Hello there... well now I believe that flowcode 8... has a facility whereby you can type in C-code ... and then it will.. 'create' flowchart (flowcode code) symbols...!! So now if you go look on the internet.. and look for a brilliant indian fellow called - Tahmid - he has a brilliant working model,...
- Sat Mar 09, 2019 8:21 am
- Forum: Flowcode V8
- Topic: Correction in nRF24L01 component
- Replies: 10
- Views: 6026
Re: Correction in nRF24L01 component
Hello ALL... I read the datasheet given to me... off the internet... and I believe that MatrixTsl's rendition of this component... is GOOD.!!! To say the least... but very confusing... and POOR.... when one realizes that there is so much of the NRF24L01 not catered for in the component..!! OR AM WRO...
- Thu Jan 31, 2019 9:26 am
- Forum: Flowcode V8
- Topic: LUT ... problem..
- Replies: 7
- Views: 4202
Re: LUT ... problem..
Hey guys - you talking RUBBISH.!!!! the software - should cater for whatever number I put into the LUT... IT IS A LOOK UP TABLE.... and so whatever number I put in there - should come out exactly the SAME.!!!.. the LUT is a STORE..!!!! NOT SO... What is the use of a LOOK UP TABLE changing the values...