Flowkit 2 Debugging Speed [Solved]
Posted: Tue Jan 23, 2018 5:52 pm
Hi Ben/ Leigh.
I am once back again with this question and concern regarding Flowkit 2,
I have done a complex project with the EB006V9 and Ghost on a 16F1937 this project involved DSP Control and many Floating point calculations
however when I run the debugger on EB006 with the Simulation speed set at Normal then
(1) the green Square will place it on the to of the flowchart and the application will run very close to real time execution
(2) verified this with the loop time of the Timers / the main loop task time 10mSec it would measure +/-11,5mSec
(3) then I can slow down the debugging with the simulation speed slider and it will slow down and I can see this also in the execution time of the code
Now when I use my Flowkit 2 on a simple Led blink program(only 1 Led ) then the
(1) green square follows through the Flowchart at a Rate of 1 too 2 Hz as if I had slowed the Simulation speed down
(2) The Simulation speed is set at normal.
I am much more familair with the Ghost functionality now and I am 100% sure the Flowkit is not working correctly there is a big difference debugging with EB006 and flowkit ,
Can you please help me out here to understand why is this in my opinion now Flowkit 2 is not usable as it is now ans I must be honest we are discussion the Flowkit since the release of FC V6 just before the release of FC 7 you guys pointer and said Ghost will be improved in V7 we are almost at V8 and fklowkit is still not working.
I apologize I am not knocking you down I am concerned about this as for me the Flowkit is ideal for updating and field testing of Proto-type controllers and there the EB006 is of no use then also on PIC32 there is no EB to develop and debug code the only variant is Flowkit 2 and I started to complain about the Flowkit operation since I used it on PIC32 just after I received it on that topic no one has ever answered the post in the Forum.
I hope you guys can help me to understand why the Flowkit2 is so slow (may be it because you use a STM-ARM in there put a dsPIC in )
Attached the flowchart and the simulation speed setting.
If you have normal speed of execution with you then I have a faulty Flowkit I would appreciate if you guys will rig up a 1937 on a EB006 test the speed and then use the Flowkit and see if I am the only one having this issue
I am once back again with this question and concern regarding Flowkit 2,
I have done a complex project with the EB006V9 and Ghost on a 16F1937 this project involved DSP Control and many Floating point calculations
however when I run the debugger on EB006 with the Simulation speed set at Normal then
(1) the green Square will place it on the to of the flowchart and the application will run very close to real time execution
(2) verified this with the loop time of the Timers / the main loop task time 10mSec it would measure +/-11,5mSec
(3) then I can slow down the debugging with the simulation speed slider and it will slow down and I can see this also in the execution time of the code
Now when I use my Flowkit 2 on a simple Led blink program(only 1 Led ) then the
(1) green square follows through the Flowchart at a Rate of 1 too 2 Hz as if I had slowed the Simulation speed down
(2) The Simulation speed is set at normal.
I am much more familair with the Ghost functionality now and I am 100% sure the Flowkit is not working correctly there is a big difference debugging with EB006 and flowkit ,
Can you please help me out here to understand why is this in my opinion now Flowkit 2 is not usable as it is now ans I must be honest we are discussion the Flowkit since the release of FC V6 just before the release of FC 7 you guys pointer and said Ghost will be improved in V7 we are almost at V8 and fklowkit is still not working.
I apologize I am not knocking you down I am concerned about this as for me the Flowkit is ideal for updating and field testing of Proto-type controllers and there the EB006 is of no use then also on PIC32 there is no EB to develop and debug code the only variant is Flowkit 2 and I started to complain about the Flowkit operation since I used it on PIC32 just after I received it on that topic no one has ever answered the post in the Forum.
I hope you guys can help me to understand why the Flowkit2 is so slow (may be it because you use a STM-ARM in there put a dsPIC in )
Attached the flowchart and the simulation speed setting.
If you have normal speed of execution with you then I have a faulty Flowkit I would appreciate if you guys will rig up a 1937 on a EB006 test the speed and then use the Flowkit and see if I am the only one having this issue