Carte EB-006 non détectée (USB)
Posted: Thu Jan 26, 2012 3:07 pm
Bonjour,
J'utilisais avec mes élèves, avec succés jusqu'à maintenant, une carte de programmation EB-006-00-7 accompagnée d'un PIC16F877A.
La semaine dernière un groupe d'étudiant connecte la carte au port USB d'un ordinateur (Windows XP) disposant de Flowcode, PPPv3 (3.11.15.30). Aucun pilote n'était installé. Ils suivirent la procédure de la documentation "Testing the board - with an external power supply."
Mais rien ne se passe, Windows XP ne detecte pas la carte et PPPv3 indique "USB cable IS NOT connected".
Alors j'installe le pilote manuellement (mchpusb.sys v1.0.0.6) trouvé dans le CD Flowcode4.
Toujours rien.
Je remplace le PIC16F877 par un autre PIC16F877, toujours rien.
Je remplace le PIC16F877 par le PIC16F88 livré d'origine et déjà programmé auparavant avec "test program RC_LVP.hex".
Je connecte la carte LED Board EB004 sur le port B et les LEDs s'illuminent correctement.
Malheureusement je ne peux toujours pas communiquer avec la carte EB006 pour programmer le PIC.
PPPv3 et Flowcode4 indiquent toujours "USB cable IS NOT connected".
Alors, QUE FAIRE ? (Ce forum est mon dernier espoir, la carte EB006 est prête pour la poubelle)
Translation :
Hello,
I used MULTIPROGRAMMER EB-006-00-7 and PIC16F877A with my students, successfully so far. Last week, students connected MULTIPROGRAMMER board to the USB port of a computer (Windows XP) with Flowcode, PPPv3 (3.11.15.30). No EB006 driver was installed.
They tested EB006 following the procedure "Testing the board - with an external power supply."
Nothing happens, Windows XP does not detect the new device and PPPv3 says "USB cable IS NOT connected".
Then I installed the driver manually (mchpusb.sys v1.0.0.6) located in the CD Flowcode4.
Still nothing.
I replaced PIC16F877A with a new PIC16F877A .
Still nothing.
I replaced the PIC16F877 by the original PIC16F88 and I connected the LED Board EB004 on B port.
PIC16F88 has still been programmed.
We then see the illumination of the LEDs, not LB3, certainly due to the "test program RC_LVP.hex" in PIC memory.
PPPv3 and Flowcode4 still indicate "USB cable IS NOT connected".
Still can't program in Flowcode.
What can I do? (Ready to throw my EB006 in the trash)
J'utilisais avec mes élèves, avec succés jusqu'à maintenant, une carte de programmation EB-006-00-7 accompagnée d'un PIC16F877A.
La semaine dernière un groupe d'étudiant connecte la carte au port USB d'un ordinateur (Windows XP) disposant de Flowcode, PPPv3 (3.11.15.30). Aucun pilote n'était installé. Ils suivirent la procédure de la documentation "Testing the board - with an external power supply."
Mais rien ne se passe, Windows XP ne detecte pas la carte et PPPv3 indique "USB cable IS NOT connected".
Alors j'installe le pilote manuellement (mchpusb.sys v1.0.0.6) trouvé dans le CD Flowcode4.
Toujours rien.
Je remplace le PIC16F877 par un autre PIC16F877, toujours rien.
Je remplace le PIC16F877 par le PIC16F88 livré d'origine et déjà programmé auparavant avec "test program RC_LVP.hex".
Je connecte la carte LED Board EB004 sur le port B et les LEDs s'illuminent correctement.
Malheureusement je ne peux toujours pas communiquer avec la carte EB006 pour programmer le PIC.
PPPv3 et Flowcode4 indiquent toujours "USB cable IS NOT connected".
Alors, QUE FAIRE ? (Ce forum est mon dernier espoir, la carte EB006 est prête pour la poubelle)
Translation :
Hello,
I used MULTIPROGRAMMER EB-006-00-7 and PIC16F877A with my students, successfully so far. Last week, students connected MULTIPROGRAMMER board to the USB port of a computer (Windows XP) with Flowcode, PPPv3 (3.11.15.30). No EB006 driver was installed.
They tested EB006 following the procedure "Testing the board - with an external power supply."
Nothing happens, Windows XP does not detect the new device and PPPv3 says "USB cable IS NOT connected".
Then I installed the driver manually (mchpusb.sys v1.0.0.6) located in the CD Flowcode4.
Still nothing.
I replaced PIC16F877A with a new PIC16F877A .
Still nothing.
I replaced the PIC16F877 by the original PIC16F88 and I connected the LED Board EB004 on B port.
PIC16F88 has still been programmed.
We then see the illumination of the LEDs, not LB3, certainly due to the "test program RC_LVP.hex" in PIC memory.
PPPv3 and Flowcode4 still indicate "USB cable IS NOT connected".
Still can't program in Flowcode.
What can I do? (Ready to throw my EB006 in the trash)