Bonjour,
Je suis sous windows 10 avec flowcode6. Je n'arrive pas à installer mon ECIO28, dans le panneau de configuration périphériques et imprimantes, il apparait quelques secondes puis disparait. J'ai mis le driver à jour, mais dans le gestionnaire de périphérique, dans propriétés de MikroElectronika USB18F device, j'ai le message: Ce périphérique ne peut pas démarrer. (Code 10). La demande spécifiée n’est pas une opération valide pour le périphérique cible.
Est ce que quelqu'un peut m'aider s'il vous plait
Merci
ECIO28 Windows10
Moderator: Benj
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: ECIO28 Windows10
Bonjour,
S'il vous plaît pouvez-vous fixer le programme de votre utilisant le dispositif ECIO . Le ECIO ne doit apparaître pendant quelques secondes après avoir été remise à zéro pour lui permettre d' être reprogrammée . Après environ 5 secondes d'être réinitialiser le ECIO se détacher de l' USB et de commencer à exécuter votre programme . Si vous souhaitez la fonctionnalité USB à partir de votre programme , vous pouvez utiliser l'un des composants USB Flowcode pour permettre cela.
Hello,
Please can you attach the program your using with the ECIO device. The ECIO should only appear for a few seconds after being reset to allow it to be reprogrammed. After about 5 seconds from being reset the ECIO will detach from the USB and begin to run your program. If you want USB functionality from within your program then you can use one of the Flowcode USB components to allow this.
S'il vous plaît pouvez-vous fixer le programme de votre utilisant le dispositif ECIO . Le ECIO ne doit apparaître pendant quelques secondes après avoir été remise à zéro pour lui permettre d' être reprogrammée . Après environ 5 secondes d'être réinitialiser le ECIO se détacher de l' USB et de commencer à exécuter votre programme . Si vous souhaitez la fonctionnalité USB à partir de votre programme , vous pouvez utiliser l'un des composants USB Flowcode pour permettre cela.
Hello,
Please can you attach the program your using with the ECIO device. The ECIO should only appear for a few seconds after being reset to allow it to be reprogrammed. After about 5 seconds from being reset the ECIO will detach from the USB and begin to run your program. If you want USB functionality from within your program then you can use one of the Flowcode USB components to allow this.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Re: ECIO28 Windows10
Bonjour,
Merci pour vos explications, je comprends pourquoi l'ECIO apparait quelques secondes puis disparait. Je me suis trompé dans la description de mon problème. Mon problème vient en fait du préprocesseur, des petits points s'affichent indéfiniment et je dois attendre plus de 3 minutes avant que le programmateur démarre (avec un programme vide). En fait je n'avais jamais attendu aussi longtemps et je croyait que cela ne fonctionnais pas mais je viens de m’apercevoir que cela fonctionne au bout de cette longue attente. Pouvez vous me dire ce qu'il faut faire pour réduire ce temps. Merci
Thank you for your explanations , I understand now why ECIO appears a few seconds and then disappears . I made a mistake in the description of my problème. My problem becomes actually from the preprocessor , small dots appear indefinitely and I have to wait more than 3 minutes before the loader starts ( with an empty program). In fact I had never waited so long and I thought it was not working but I just noticed that it works after this long wait . Can you tell me what to do to reduce this time please. Thank you.
Merci pour vos explications, je comprends pourquoi l'ECIO apparait quelques secondes puis disparait. Je me suis trompé dans la description de mon problème. Mon problème vient en fait du préprocesseur, des petits points s'affichent indéfiniment et je dois attendre plus de 3 minutes avant que le programmateur démarre (avec un programme vide). En fait je n'avais jamais attendu aussi longtemps et je croyait que cela ne fonctionnais pas mais je viens de m’apercevoir que cela fonctionne au bout de cette longue attente. Pouvez vous me dire ce qu'il faut faire pour réduire ce temps. Merci
Thank you for your explanations , I understand now why ECIO appears a few seconds and then disappears . I made a mistake in the description of my problème. My problem becomes actually from the preprocessor , small dots appear indefinitely and I have to wait more than 3 minutes before the loader starts ( with an empty program). In fact I had never waited so long and I thought it was not working but I just noticed that it works after this long wait . Can you tell me what to do to reduce this time please. Thank you.
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: ECIO28 Windows10
Bonjour,
Oui cela ressemble à un problème , la compilation ne devrait pas durer près aussi longtemps avec un programme vide . Flowcode v6 et l'utilisation précédente du compilateur BoostC qui est assez lent pour compiler déjà, mais ne devraient pas prendre ce temps pour terminer avec un programme vide. Je dirais que votre antivirus ou pare-feu est à l'origine de la longue période de compilation. Une façon de contourner cela est de «liste blanche» le répertoire Flowcode dans votre logiciel antivirus / pare-feu et que devrait permettre la compilation de terminer sans être constamment recherche de virus.
Hello,
Yes that sounds like a problem, the compilation should not take anywhere near that long with an empty program. Flowcode v6 and previous use the BoostC compiler which is quite slow to compile already but should not be taking that long to complete with a blank program. My guess would be that your Antivirus or Firewall is causing the long compilation time. One way to work around this is to "White List" the Flowcode directory in your AntiVirus/Firewall software and that should allow the compilation to complete without being constantly scanned for viruses.
Oui cela ressemble à un problème , la compilation ne devrait pas durer près aussi longtemps avec un programme vide . Flowcode v6 et l'utilisation précédente du compilateur BoostC qui est assez lent pour compiler déjà, mais ne devraient pas prendre ce temps pour terminer avec un programme vide. Je dirais que votre antivirus ou pare-feu est à l'origine de la longue période de compilation. Une façon de contourner cela est de «liste blanche» le répertoire Flowcode dans votre logiciel antivirus / pare-feu et que devrait permettre la compilation de terminer sans être constamment recherche de virus.
Hello,
Yes that sounds like a problem, the compilation should not take anywhere near that long with an empty program. Flowcode v6 and previous use the BoostC compiler which is quite slow to compile already but should not be taking that long to complete with a blank program. My guess would be that your Antivirus or Firewall is causing the long compilation time. One way to work around this is to "White List" the Flowcode directory in your AntiVirus/Firewall software and that should allow the compilation to complete without being constantly scanned for viruses.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Re: ECIO28 Windows10
bonjour,
En effet, quand je stoppe l'antivirus, cela va plus vite, environ 20s. Il ne me reste plus qu'à trouver la liste blanche dont vous parlez. Merci pour votre aide.
Cordialement
Hello,
Indeed, when I quit the antivirus, the compilation goes faster, approximately 20s . It remains for me to find the white list you are speaking about. Thank you for your help.
cordially
Philippe
En effet, quand je stoppe l'antivirus, cela va plus vite, environ 20s. Il ne me reste plus qu'à trouver la liste blanche dont vous parlez. Merci pour votre aide.
Cordialement
Hello,
Indeed, when I quit the antivirus, the compilation goes faster, approximately 20s . It remains for me to find the white list you are speaking about. Thank you for your help.
cordially
Philippe
Re: ECIO28 Windows10
Bonjour,
J'ai mis Flowcode6, pp.exe et boostc_18.exe dans les applications de confiance Kaspersky mais cela ne change rien, il faut plusieurs minutes pour arriver au téléchargement dans la cible. Si je désactive Kaspersky, il faut encore environ 45 secondes, c'est long!
Y a t-il une solution à ce problème ?
Hello,
I put Flowcode6 , Pp.exe and boostc_18.exe in Kaspersky trusted applications, but it does make any change , it takes several minutes to download in the target. If I disable Kaspersky, it still takes about 45 seconds, it's a long time !
Is there a solution to this problem?
cordially
Philippe
J'ai mis Flowcode6, pp.exe et boostc_18.exe dans les applications de confiance Kaspersky mais cela ne change rien, il faut plusieurs minutes pour arriver au téléchargement dans la cible. Si je désactive Kaspersky, il faut encore environ 45 secondes, c'est long!
Y a t-il une solution à ce problème ?
Hello,
I put Flowcode6 , Pp.exe and boostc_18.exe in Kaspersky trusted applications, but it does make any change , it takes several minutes to download in the target. If I disable Kaspersky, it still takes about 45 seconds, it's a long time !
Is there a solution to this problem?
cordially
Philippe
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: ECIO28 Windows10
Hello Philippe,
Try also adding these exe's to the trusted applications list.
C:\Program Files (x86)\Flowcode 6\compilers\pic\boostc\fc_launcher.exe
C:\Program Files (x86)\Flowcode 6\compilers\pic\boostc\linker.exe
Try also adding these exe's to the trusted applications list.
C:\Program Files (x86)\Flowcode 6\compilers\pic\boostc\fc_launcher.exe
C:\Program Files (x86)\Flowcode 6\compilers\pic\boostc\linker.exe
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel