Hallo to all.
is there an example code, or a way to realize a 2 phase interleaved buck converter for FC8 , as in the design file ( page 8, figure 10 ) below ? It gives the MPLAB X project files, but I would like to realize that with FC8 .
2 PHASE INTERLEAVED BUCK CONTROLLER
Moderator: Benj
-
- Posts: 115
- Joined: Wed Aug 03, 2016 10:45 pm
- Has thanked: 24 times
- Been thanked: 11 times
- Contact:
2 PHASE INTERLEAVED BUCK CONTROLLER
- Attachments
-
- TB3155-Multiphase-Interleaved-PWM-Controller-with-Diode-Emulation-DS90003155B.pdf
- (688.19 KiB) Downloaded 194 times
- QMESAR
- Valued Contributor
- Posts: 1287
- Joined: Sun Oct 05, 2014 3:20 pm
- Location: Russia
- Has thanked: 384 times
- Been thanked: 614 times
- Contact:
Re: 2 PHASE INTERLEAVED BUCK CONTROLLER
Hi.
I am afraid that there is no FC components that does this for you with that said, you can do all of this in FC8 by using a C call Icon's and setup
the PIC peripherals as needed .
I have done buck converters in FC 7 using this method
(1) use MPLABX Code configurator to generate you the configurations for the peripherals such as CLC and PWM modules
(2) The code are in the relative header / c files for the modules
(3) copy and paste the code into a C icon where necessary
(4) run the code as usual in FC where needed meaning the driver code such as setting the PWM duty cycle for example
Hope this helps
I am afraid that there is no FC components that does this for you with that said, you can do all of this in FC8 by using a C call Icon's and setup
the PIC peripherals as needed .
I have done buck converters in FC 7 using this method
(1) use MPLABX Code configurator to generate you the configurations for the peripherals such as CLC and PWM modules
(2) The code are in the relative header / c files for the modules
(3) copy and paste the code into a C icon where necessary
(4) run the code as usual in FC where needed meaning the driver code such as setting the PWM duty cycle for example
Hope this helps
https://www.flowcodexchange.com/
Regards QMESAR
Regards QMESAR
- Steve001
- Valued Contributor
- Posts: 1189
- Joined: Wed Dec 31, 2008 3:37 pm
- Has thanked: 460 times
- Been thanked: 523 times
- Contact:
Re: 2 PHASE INTERLEAVED BUCK CONTROLLER
Hi SILVESTROS9
Are you using this for a PSU aplication ? - PDF Not downloading for me
Have you seen Texas Instruments "Web Bench" PSU designer
http://www.ti.com/design-resources/desi ... gner.html#
https://webench.ti.com/power-designer/s ... -regulator
I have used this to design a couple of DCDC Convertors - you can download all the desgin infomation coil winding data BOM's etc.
It Also generates PCB Layouts (Eagle Format)
Steve
Are you using this for a PSU aplication ? - PDF Not downloading for me
Have you seen Texas Instruments "Web Bench" PSU designer
http://www.ti.com/design-resources/desi ... gner.html#
https://webench.ti.com/power-designer/s ... -regulator
I have used this to design a couple of DCDC Convertors - you can download all the desgin infomation coil winding data BOM's etc.
It Also generates PCB Layouts (Eagle Format)
Steve
- Attachments
-
- Annotation 2019-10-06 184444.png
- (72.81 KiB) Downloaded 593 times
Success always occurs in private and failure in full view.