Search found 12 matches

Return

by medelec35
Sun Sep 27, 2015 12:35 pm
Jump to forum
Jump to topic

Re: Electronic Workstation v.1.0 - drivers & softs

Hi Zamphy, The latest drivers for the test pod (USBee sx Test Pod) can be downloaded from selecting USBee SX Downloads on this link The drivers are within USBee SX Digital Test Pod Software (32-bit) USBee SX Digital Test Pod Software (64-bit) I have got the USBee Analyser and USBee Generator and it ...
by DavidA
Fri Oct 09, 2015 11:58 am
Jump to forum
Jump to topic

Re: Electronic Workstation v.1.0 - drivers & softs

Hello,

Have you tried disabling driver signing enforcement and installing the drivers?

http://www.matrixtsl.com/faq/index.php? ... artlang=en
by Benj
Mon Oct 12, 2015 3:45 pm
Jump to forum
Jump to topic

Re: Electronic Workstation v.1.0 - drivers & softs

Hello, These are the drivers required by the PC interface component in the workstation. These drivers are signed so should work as is but let us know how you get on. E-Workstation.zip ECIO28.zip The workstation contains a USB hub and so the hub might potentially be having a problem. Have you tried c...
by Benj
Tue Oct 20, 2015 11:47 am
Jump to forum
Jump to topic

Re: Electronic Workstation v.1.0 - drivers & softs

Hello, The output of the PC interface is driven from your PC. If your PC is busy doing something else or maybe a bit low on power then the timing glitches you are seeing are to be expected. It's basically Windows jumping in and out of the application to try and do everything at once. However if your...
by medelec35
Wed Nov 08, 2017 10:07 am
Jump to forum
Jump to topic

Re: ECIO28 and ECIO40P drivers trouble - Win10

Hi
Have you tried the drivers from here?

I have not long got a new 64bit windows 10 PC
I will need to install ECIO drivers when I get home tonight.
Will can post on here how I got on.
In the past I have used the drives from the above link with no issues.
That was also with 64bit windows.

Martin
by medelec35
Thu Nov 09, 2017 6:50 pm
Jump to forum
Jump to topic

Re: ECIO28 and ECIO40P drivers trouble - Win10

I thought I would first try the drivers from the Matrix Web shop Installed without any issue on my 64 Bit windows 10 Home Version 10.0.15063 Build 15063. Created a simple flasher to test my ECIO40. Programmed and ran with no issues. So it looks like the signed version that's on the main website is t...
by jadiflow
Sun Apr 29, 2018 8:55 am
Jump to forum
Jump to topic

Re: gLCD ILI9341 - Pins correspondence to Flowcode Connections

It seems your display has two options for connections, serial connection and parallel connection. The FC pins are for the serial connection. The pins D4, D5, D6, D7, WR, are for a parallel connection and you don't need those for the serial link. For the serial link you only need clock, chip select a...
by kersing
Sun Apr 29, 2018 9:52 am
Jump to forum
Jump to topic

Re: gLCD ILI9341 - Pins correspondence to Flowcode Connections

This display controller has several options to interface with other hardware. The vendor of this board has chosen to configure the controller in 8 bit parallel mode (done on the PCB, can't be changed by software, data sheet see page 26). The Flowcode component can only be used for a display configur...
by jgu1
Sun Apr 29, 2018 11:46 am
Jump to forum
Jump to topic

Re: gLCD ILI9341 - Pins correspondence to Flowcode Connections

Hi zamphy! I use these display with Arduino mega: https://www.ebay.com/itm/2-8-TFT-LCD-Display-Touch-Panel-SPI-Serial-240-320-ILI9341-5V-3-3V-STM32/201950756171?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2648 And they work very well with FC7. :D But remember only 3,3Volt supply and da...
by Benj
Mon May 28, 2018 7:47 pm
Jump to forum
Jump to topic

Re: EB650 - DSP Audio Training Solution - where is it ??

Hi Zamphy,

I believe this is the link you're after. Found it by searching the site for audio.

http://www.matrixtsl.com/resources/getr ... hp?id=1004
by Benj
Fri Oct 12, 2018 5:57 pm
Jump to forum
Jump to topic

Re: FC7.2.1.4 - Where are the gLCD pins connections ?

Hello, The displays on the ST Discovery dev boards are configured by the underlying ST ARM C library and the IO pins are fixed hence not available as properties. You could potentially be zoomed in too close on the 3D panel, try toggling the perspective button at the top of the panel window and see i...
by Benj
Fri Oct 12, 2018 8:46 pm
Jump to forum
Jump to topic

Re: FC7.2.1.4 - Where are the gLCD pins connections ?

I tried a lot with zoom in the 3D Panel, but really I can´t see any trace of them. This is starting to ring a bell, I'll investigate for you. So, is it impossible to use these 3 display with PIC micorocontrollers ? Yes currently these three displays are quite complex to drive at a good speed and so...