Hallo,
das modifizierte Programm ändert den Takt nicht.
Das Problem dürfte daran liegen, dass keine Konfiguration mit dem Hex-File übertragen wird.
Was muss ich einstellen damit die Konfiguration mit übertragen wird.
Mit freundlichen Grüßen
HjH
Search found 108 matches
- Thu Sep 08, 2011 4:51 pm
- Forum: Deutsch Support-Forum
- Topic: 48MHz lassen sich nicht einstellen
- Replies: 16
- Views: 11625
- Thu Sep 08, 2011 11:48 am
- Forum: Deutsch Support-Forum
- Topic: 48MHz lassen sich nicht einstellen
- Replies: 16
- Views: 11625
Re: 48MHz lassen sich nicht einstellen
Hi,
ich habe die Befehlszeile in mein Programm eingefügt.
Leider hat dies keine Auswirkungen auf den Takt.
Mit freundlichen Grüßen
HjH
ich habe die Befehlszeile in mein Programm eingefügt.
Leider hat dies keine Auswirkungen auf den Takt.
Mit freundlichen Grüßen
HjH
- Wed Sep 07, 2011 10:20 pm
- Forum: Deutsch Support-Forum
- Topic: 48MHz lassen sich nicht einstellen
- Replies: 16
- Views: 11625
Re: 48MHz lassen sich nicht einstellen
Hallo, leider bekomme ich folgende Fehlermeldung nach dem ich Ihren Programmschnipsel eingesetzt habe: USB_Test_1.c(171): error: left operand must be l-value USB_Test_1.c(171:16): error: failed to generate expression Daraufhin habe ich folgende Programmzeilen eingefügt volatile char _pllen @PLLEN; u...
- Wed Sep 07, 2011 3:39 pm
- Forum: Deutsch Support-Forum
- Topic: 48MHz lassen sich nicht einstellen
- Replies: 16
- Views: 11625
Re: 48MHz lassen sich nicht einstellen
Hello, ich habe Ihren Programmabschnitt in mein Programm eingefügt. Daraufhin bekam ich folgende Fehlermeldung: USB_Test_1.c(177:2): error: unknown identifier 'OSCTUNEbits' USB_Test_1.c(177:2): error: failed to generate expression USB_Test_1.c(177:2): error: invalid operand 'OSCTUNEbits.0x00000006' ...
- Wed Sep 07, 2011 12:00 am
- Forum: Deutsch Support-Forum
- Topic: 48MHz lassen sich nicht einstellen
- Replies: 16
- Views: 11625
48MHz lassen sich nicht einstellen
Hallo, Ich habe einen PIC 18F25J50 und möchte diesen mit einer Frequenz von 48MHz betreiben. Am 18F25J50 ist ein externes 12MHz Quarz angeschlossen. Leider lässt sich der PIC nicht auf 48MHz einstellen, weder intern noch extern (siehe Anhang). Laut meinem Oszilloskop hätte ich am Ausgang 8.33Hz stat...
- Tue Sep 06, 2011 5:08 pm
- Forum: Deutsch Support-Forum
- Topic: I2C Error
- Replies: 2
- Views: 3625
Re: I2C Error
Danke für die Hilfe
- Tue Sep 06, 2011 12:59 am
- Forum: Deutsch Support-Forum
- Topic: I2C Error
- Replies: 2
- Views: 3625
I2C Error
Hallo ich will mit einem 24F16KA102 eine I2C EEPROM beschreiben. Leider bekomme ich beim kompilieren folgende Fehlermeldungen. ExtEEPROM.c: In function 'FCD_I2C_Master0_MI2C_Init': ExtEEPROM.c:676: error: 'I2CCONbits' undeclared (first use in this function) ExtEEPROM.c:676: error: (Each undeclared i...
- Mon Sep 05, 2011 4:52 pm
- Forum: Deutsch Support-Forum
- Topic: USB läuft nicht auf dem 18F14K50
- Replies: 6
- Views: 5972
Re: USB läuft nicht auf dem 18F14K50
Hallo Benj,
vielen Dank für Ihre Unterstützung. Den Treiber noch einmal über den Device Manager zu installieren wahr eine gute Idee.
Jetzt läuft der USB mit dem 18F14K50 auch bei mir!
vielen Dank für Ihre Unterstützung. Den Treiber noch einmal über den Device Manager zu installieren wahr eine gute Idee.
Jetzt läuft der USB mit dem 18F14K50 auch bei mir!
- Fri Sep 02, 2011 11:51 pm
- Forum: Deutsch Support-Forum
- Topic: USB läuft nicht auf dem 18F14K50
- Replies: 6
- Views: 5972
Re: USB läuft nicht auf dem 18F14K50
Hallo Benj, vielen Dank für Deine E-Mail. Leider finde ich keinen Treiber den ich im Gerätemanager installieren könnte. Irgendetwas ist an meinem Programm noch falsch, denn Windows gibt keinen Hinweis darauf, dass ein USB Gerät angeschlossen wurde und Windows den Geräte-Treiber installieren möchte. ...
- Thu Sep 01, 2011 11:45 pm
- Forum: Deutsch Support-Forum
- Topic: USB läuft nicht auf dem 18F14K50
- Replies: 6
- Views: 5972
Re: USB läuft nicht auf dem 18F14K50
Hallo Benj, vielen Dank für Deine E-Mail. Ich habe über „Generate Driver File“ die Datei zum Installieren generiert (siehe Anhang Zip-Datei). Leider bekomme ich immer die Fehlermeldung „Diese Installationsmethode wird von der ausgewählten INF-Datei nicht unterstützt“ Kann diese Fehlermeldung viellei...
- Sun Aug 28, 2011 3:47 pm
- Forum: Deutsch Support-Forum
- Topic: USB läuft nicht auf dem 18F14K50
- Replies: 6
- Views: 5972
USB läuft nicht auf dem 18F14K50
Hallo, ich wende mich an das deutsche Support- Forum in der Hoffnung dort besseren Support zu bekommen als auf der englischen Support-Seite. Ich habe ein "USB Development Kit " von Microchip und will eine USB/RS232 Schnittstelle entwerfen. Als erstes versuchte ich eine RS232 Verbindung über den USB ...
- Tue Aug 23, 2011 6:12 pm
- Forum: Flowcode V4
- Topic: Error in the EEPROMRead definition
- Replies: 1
- Views: 1714
Error in the EEPROMRead definition
Hallo, the controler is a 16LF1939 with 16MHz tact. I will write in and read from the EEPROM. I add in my program the eeprom component i get after compile the following error message. DatenLogger16LF1639.c(1830): Illegal redefinition of symbol: MX_EEADR DatenLogger16LF1639.c(1841): Illegal redefinit...
- Sun Aug 07, 2011 10:50 pm
- Forum: Flowcode V4
- Topic: Error in the ADC definition
- Replies: 10
- Views: 9523
Error in the ADC definition
Hallo, the controler is a 16LF1939 with 16MHz tact. I could not read the 13 ADC Channels with the Flowcode ADC-component. The results of measuring was wild numbers. After my correction of the codes the result was sent correct, but the result had the average deviation from 1.1 %. The maximum deviatio...
- Sun Jul 31, 2011 3:15 pm
- Forum: Flowcode V4
- Topic: Mistake of setting the oscillator configuration of 18f25j50
- Replies: 1
- Views: 1650
Mistake of setting the oscillator configuration of 18f25j50
Hi I have a 18F25J50 microcontroler with 12 MHz quartz. I can't correctly setting the oscillatorfrequenc of the 18F25J50. Every setting in the "PPP" have the same mistake clock pulse. In the example the clock pulse at RC2 should be at 1Hz, actually he has 0.33 Hz What I am doing wrong Flowcode_test_...
- Sat Jul 30, 2011 10:18 pm
- Forum: Flowcode V4
- Topic: Error in the SPI definition
- Replies: 1
- Views: 2409
Error in the SPI definition
Hallo, the controler is a 24FJ128GA010 on the explorer board. I will write in a SPI EEPROM The programm compiled with following errors: Explorer_Test1.c: In function 'FCD_SPI_Legacy0_SPI_Init': Explorer_Test1.c:990: error: 'SPI1CON' undeclared (first use in this function) Explorer_Test1.c:990: error...
- Sun Jul 17, 2011 11:35 pm
- Forum: Flowcode V4
- Topic: I can't receive Bytes from MCP9800
- Replies: 3
- Views: 2590
Re: I can't receive Bytes from MCP9800
Hi
here is my code
here is my code
- Sun Jul 17, 2011 11:29 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi
this Problem will occur at BootC on. With HITECH let the program does not compile without error
this Problem will occur at BootC on. With HITECH let the program does not compile without error
- Sun Jul 10, 2011 7:19 pm
- Forum: Flowcode V4
- Topic: Big bug with ADC
- Replies: 1
- Views: 1576
Big bug with ADC
Hi I have write a smal sample, that can explain the bug. The bug is in the call "ReadAsVoltage" If you replace the 0.01 in the call "fVoltage = float32_mul(fVoltage, 0.01);" with integer number and the 0.000976 in the call "fVperDiv = float32_mul(fVoltage, 0.000976);" with integer number the complie...
- Sun Jul 10, 2011 12:36 pm
- Forum: Flowcode V4
- Topic: I can't receive Bytes from MCP9800
- Replies: 3
- Views: 2590
I can't receive Bytes from MCP9800
Hi
I can't receive Bytes from MCP9800. This is my first I2C project.
Have anybody a smal example that can receive Bytes from MCP9800.
I can't receive Bytes from MCP9800. This is my first I2C project.
Have anybody a smal example that can receive Bytes from MCP9800.
- Sun Jul 03, 2011 2:41 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi
thank you for the help.
Now I have a new problem. Your programm breaks up, if I write the hex file in the 18F14K50. You can see the error in the attachment
thank you for the help.
Now I have a new problem. Your programm breaks up, if I write the hex file in the 18F14K50. You can see the error in the attachment
- Thu Jun 30, 2011 11:05 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi
Here is my file
Here is my file
- Wed Jun 29, 2011 10:30 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi
Which Flowcode USB component are you using in your program?
The Flowcode USB component is "Flowcode USB Serial"
Can you attach your Flowcode program to the forums?
I've been told I may not publish my program in the forum.
Which Flowcode USB component are you using in your program?
The Flowcode USB component is "Flowcode USB Serial"
Can you attach your Flowcode program to the forums?
I've been told I may not publish my program in the forum.
- Fri Jun 24, 2011 3:55 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi
The version looks after from Matrix (v4.5). They told me I should consult the forum.
The USB component see File.
The version looks after from Matrix (v4.5). They told me I should consult the forum.
The USB component see File.
- Fri Jun 24, 2011 2:53 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
Re: I have a big Problem with the USB-Driver
Hi I generate the inv File, with Flowcode "Generate Drive File" button from the USB component property page. "Have you tried going into device manager, selecting the device, clicking install driver and then pointing the wizard at the Flowcode generated inf file" I did this. I got the error message "...
- Fri Jun 24, 2011 1:41 pm
- Forum: Flowcode V4
- Topic: I have a big Problem with the USB-Driver
- Replies: 13
- Views: 6718
I have a big Problem with the USB-Driver
I have a big Problem with the USB-Driver. - My operating system is Windows 7 64bit "Home premium". - My test board is a "Low Pin Count USB Development Kit" from Microchip. - I have written a USB progam in Flowcode. - I transmitted this program in the 18F14K50 controller, without errors - I start the...