Search found 10 matches

by dickcheung
Sun Aug 26, 2012 10:24 am
Forum: Flowcode V2 & V3
Topic: Using Flowcode with the TINY PIC Bootloader
Replies: 6
Views: 14810

Re: Using Flowcode with the TINY PIC Bootloader

Dear Benj, OK, thanks so much :D , I will try this later on as not in my desk. Maybe last time I selected ECIO instead of real chip :oops: . Thanks again. Dick Hello Dick, So, is there any method that can be simply using the files generted from flowcode and then download to the chips using 3rd party...
by dickcheung
Fri Aug 24, 2012 2:35 am
Forum: Flowcode V2 & V3
Topic: Using Flowcode with the TINY PIC Bootloader
Replies: 6
Views: 14810

Re: Using Flowcode with the TINY PIC Bootloader

Dear Benj, I am new to this, actually, I have my own programmer that allow downloaded the files to different chips. I simply tried to generate files from flowcode, and then downloaded the file to a new PIC chip (877A without any bootloader) throught that universal programmer (not through flowcode), ...
by dickcheung
Sun Dec 18, 2011 4:40 pm
Forum: E-blocks
Topic: ECIO with gLCD EB058
Replies: 8
Views: 6706

Re: ECIO with gLCD EB058

Hi Pete, Thanks so much for your great help. I will try this for sure later on. And hope Benj will give help soon. Thanks again. Dick Hi Dick, I had a similar issue with my gLCD.. It appeared to be a bonding problem with the ribbon cable to either board or display. Don't think that there is much you...
by dickcheung
Tue Dec 13, 2011 8:54 am
Forum: E-blocks
Topic: ECIO with gLCD EB058
Replies: 8
Views: 6706

ECIO with gLCD EB058

Hi, I am new to gLCD, and currently use my ECIO (28P) to control the EB058. In another pages, big brother has recommended good steps and suggestions on how to control EB058, I have tried and successfully turn it on. However, the screen display some unwanted vertical color lines at the left/right sid...
by dickcheung
Sun Dec 11, 2011 2:09 pm
Forum: Formula Flowcode
Topic: gLCD with Formula Flowcode
Replies: 14
Views: 26361

Re: gLCD with Formula Flowcode

Hi Benj, Thanks for your great suggestions, I am currently tried to use the gLCD (EB0058) to my ECIO (28P), per your below description, I set my gLCD to: - (a.)patch, port B, s/w mode, (b) B, port B, s/w mode, both settings are work. - CS as bit 0. - in flowcode, the properties set to EB0057 as no s...
by dickcheung
Thu Aug 04, 2011 5:17 am
Forum: General Programming
Topic: About Graphic LCD and ADC
Replies: 6
Views: 5251

Re: About Graphic LCD and ADC

Thanks Benj's quick reponse, For both B/W and color LCD, I just use the downloaded testing program, and changed the chip as ECIO28P, and the port as below (and attached screen capture): B/W LCD: Data 1: PORT B bit 0 Data 2: PORT B bit 1 Data 3: PORT B bit 2 Data 4: PORT B bit 3 RS: PORT B bit 4 Enab...
by dickcheung
Tue Aug 02, 2011 11:23 am
Forum: General Programming
Topic: About Graphic LCD and ADC
Replies: 6
Views: 5251

Re: About Graphic LCD and ADC

Hi Sir, I tried but the color LCD still can't function. Besides, I also have the B/W LCD e-block, this time it only can show up a very dark blocks instead of letters. I have use screw driver to tune the contrast but simple observe from "no display" to dark blocks, still not found any letters. I use ...
by dickcheung
Fri Jul 15, 2011 5:01 pm
Forum: General Programming
Topic: About Graphic LCD and ADC
Replies: 6
Views: 5251

Re: About Graphic LCD and ADC

Thanks so much to John Crow and Ben Rowland, I will try this now and see if I can do so..

Thanks again~ :D
by dickcheung
Fri Jul 15, 2011 5:19 am
Forum: General Programming
Topic: About Graphic LCD and ADC
Replies: 6
Views: 5251

About Graphic LCD and ADC

Hi All, it's me again - a new comer-, would like to ask below comments, 1)EB-058 color graphic LCD E-Block ) I tried to use this in ECIO28P(with EB061), and tried different setting and jumper setting, but couldn't get any display on the LCD, may I ask for your help on what setting should be? (port s...
by dickcheung
Fri Jul 01, 2011 8:46 am
Forum: Flowcode V4
Topic: New to Flowcode, ask for help on servo control
Replies: 2
Views: 2304

New to Flowcode, ask for help on servo control

Hi all big brother, I am new to this, currently I have brought a bundle Flowcode V4 with EB-061+ECIO28P, and now trying to use the servo component to control some servo, however, I encountered compile problem, it pop out a warning that told me about this version of flowcode only compile below compon...