Search found 262 matches

by STibor
Sun Sep 22, 2019 2:42 pm
Forum: Bug Reports
Topic: Bad mistake in FC8!
Replies: 15
Views: 1031

Re: Bad mistake in FC8!

Just happened: during a simulation added a few variables in the simulation debugger. Run simulation, pause, add variable (has always been a normal process) and immediately the shutdown window has appeared. No chance to save! Christina Hello, Mystical bug. Macro "ok and edit button bug" 3 ...
by STibor
Sat Aug 17, 2019 12:07 pm
Forum: Flowcode V8
Topic: Pure Sine Wave Inverter
Replies: 10
Views: 879

Re: Pure Sine Wave Inverter

Hello,

Component: Frequency Generator (DSP)
Basic Sine Wave Generator:https://www.matrixtsl.com/wiki/index.php?title=Component:_Frequency_Generator_(DSP)
by STibor
Mon Jun 17, 2019 5:28 am
Forum: 32-Bit ARM
Topic: Store Flash Data (Eeprom?) STM32F051
Replies: 8
Views: 2070

Re: Store Flash Data (Eeprom?) STM32F051

Hello!
Excellent work!
If the page block is not empty, you cannot write data.
How do I delete the data stored on the page?
by STibor
Fri Jun 14, 2019 8:00 am
Forum: Bug Reports
Topic: Macro OK and Edit button problem
Replies: 1
Views: 438

Re: Macro OK and Edit button problem

Hello!

Will there be a fix for the error sometime?
by STibor
Mon May 20, 2019 4:35 pm
Forum: Bug Reports
Topic: Macro OK and Edit button problem
Replies: 1
Views: 438

Macro OK and Edit button problem

Hello,

The macro ok and edit button sometimes does not open the macro, it just closes.
If get the macro parameter, the program opens the macro.
https://www.youtube.com/watch?v=i1nyNOprM58&feature=youtu.be
by STibor
Wed May 08, 2019 8:11 pm
Forum: Flowcode V8
Topic: Flowcode 8.2 crash
Replies: 7
Views: 958

Re: Flowcode 8.2 crash

Please can you try the following and let us know how you get on. Open Flowcode. Click View -> Global Options. Click the Application tab. Click the "Reset Data Files" button. Click Yes on the dialogue window that opens. Close Flowcode and then try to open your project again. Thanks! That's...
by STibor
Wed May 08, 2019 2:06 pm
Forum: Flowcode V8
Topic: Flowcode 8.2 crash
Replies: 7
Views: 958

Re: Flowcode 8.2 crash

I can't create a new project.
1. Flowcode opens
2. embedded
3 target selection Arduino nano 328, okay button, and then the program freezes.
by STibor
Wed May 08, 2019 1:22 pm
Forum: Flowcode V8
Topic: Flowcode 8.2 crash
Replies: 7
Views: 958

Re: Flowcode 8.2 crash

I uninstalled the old one and installed the full version 8.2. Crashes while loading the project.
Arduino nano uart rx interrupt macro stops loading.
by STibor
Wed May 08, 2019 1:08 pm
Forum: Flowcode V8
Topic: Flowcode 8.2 crash
Replies: 7
Views: 958

Flowcode 8.2 crash

Hello,

I updated patch 8.1 to 8.2.
The ongoing project is not loading, Flowcode freezes.
That's not very good now.
by STibor
Thu Apr 04, 2019 7:03 am
Forum: Bug Reports
Topic: Hidden Flowchart icons
Replies: 3
Views: 799

Re: Hidden Flowchart icons

Hello,

Will there be a solution to the problem?

Thanks!
by STibor
Sun Jan 27, 2019 5:19 pm
Forum: Flowcode V8
Topic: SCADA without Components-Macro
Replies: 1
Views: 539

Re: SCADA without Components-Macro

Hello!

Use the simulation macro icon.
by STibor
Mon Jan 21, 2019 6:15 pm
Forum: Bug Reports
Topic: Hidden Flowchart icons
Replies: 3
Views: 799

Hidden Flowchart icons

Hello!
The 2D 3D window covers the left-hand flowchart icons.
by STibor
Mon Jan 21, 2019 5:59 pm
Forum: Bug Reports
Topic: Same updates reoccurring after download completion.[Fixed]
Replies: 9
Views: 1563

Re: Same updates reoccurring after download completion.

Hi Martin, We did create a problem with the RPI targets. We thought we had fixed it but maybe this is just if you didn't download updates while the broken files were available. You should be able to delete the contents of your "C:\ProgramData\MatrixTSL\FlowcodeV8" folder to effectively st...
by STibor
Sat Dec 15, 2018 6:30 am
Forum: Bug Reports
Topic: Arduino Nano328 UART bug
Replies: 2
Views: 817

Re: Arduino Nano328 UART bug

Thanks!
I have restored the AVR_CAL_UART.c file, from revision 5 to revision 4.
It works like this.
by STibor
Fri Dec 14, 2018 9:05 pm
Forum: Bug Reports
Topic: Arduino Nano328 UART bug
Replies: 2
Views: 817

Arduino Nano328 UART bug

Hello,

UART component generates the following error:
(I think it was good before the last update.)
by STibor
Wed Dec 12, 2018 7:54 pm
Forum: Bug Reports
Topic: BitmapDrawerFAT bug
Replies: 2
Views: 575

Re: BitmapDrawerFAT bug

Hello! Thanks. I tested it, it was better, but not good. I attach the picture. Another problem is that it is very slow. In the simulator I do not display the image on the display. (other test) I can not see the display on the 3D system panel and there are not any other components. (other test) You u...
by STibor
Tue Dec 11, 2018 9:30 pm
Forum: Bug Reports
Topic: BitmapDrawerFAT bug
Replies: 2
Views: 575

BitmapDrawerFAT bug

Hello,

Hardware: STM32F746 Disco
The image is displayed incorrectly.
If the image data: 450 * 255 landscape orientation, the program freezes.
If the image is 480 * 272 pixels, only a 15-pixel wide bar will be displayed.
by STibor
Thu Dec 06, 2018 7:30 pm
Forum: Flowcode V8
Topic: PIC16F1937 reference voltage for A/D-conversion
Replies: 5
Views: 953

Re: PIC16F1937 reference voltage for A/D-conversion

Hello,

Have you planned to expand the ADC component of other types of controllers with FVR?
For example: Arduino Nano, Uno, Mega, PIC12F1822
by STibor
Tue Nov 27, 2018 8:29 pm
Forum: Flowcode V8
Topic: Comparator PC10f204
Replies: 6
Views: 1279

Re: Comparator PC10f204

Hello!

I attach an example.
Not tested in hardware.
by STibor
Tue Nov 20, 2018 5:40 pm
Forum: Bug Reports
Topic: Import old projects
Replies: 5
Views: 1204

Re: Import old projects

Hello, Do you have many files to upgrade? We recently removed v4 and v5 upgrade support from v8.1. You can send me the files via PM and I will convert them to v8 for you. Thanks! I understand how difficult it is to hold together different software versions. Old Flowcode versions are also installed ...
by STibor
Tue Nov 20, 2018 6:30 am
Forum: Bug Reports
Topic: Import old projects
Replies: 5
Views: 1204

Import old projects

Hello!

I bought the Flowcode v8 program, thank you for the extra black Friday 30% discount. :D

How to import old Flowcode v4 and v5 project files?
I can not find the import function in the file menu.
by STibor
Wed Nov 14, 2018 5:35 pm
Forum: Bug reports
Topic: PIC18F25K80 timer1 problem
Replies: 4
Views: 1165

Re: PIC18F25K80 timer1 problem

I modified the fcd file.
I replaced T1SOSCEN to SOSCEN.
This is how the timer1 interruption works well.
by STibor
Wed Nov 14, 2018 12:50 pm
Forum: Bug reports
Topic: PIC18F25K80 timer1 problem
Replies: 4
Views: 1165

Re: PIC18F25K80 timer1 problem

Thanks,

I know the syntax but there is nothing T1CON, T1SOSCEN bit, only T1CON, SOSCEN.
I think you've passed the bug from an old version of V6.
by STibor
Wed Nov 14, 2018 10:25 am
Forum: Bug reports
Topic: PIC18F25K80 timer1 problem
Replies: 4
Views: 1165

PIC18F25K80 timer1 problem

Hello!

I compiled an old v6 project in v7.
An old "T1SOSCEN error" emerged.
Old thread: http://www.matrixtsl.com/mmforums/viewtopic.php?f=59&t=17312
by STibor
Fri Nov 09, 2018 12:45 pm
Forum: Flowcode V7
Topic: MPU 6050 X Y Z degree outputs
Replies: 3
Views: 1002

Re: MPU 6050 X Y Z degree outputs

Hello!

I set the two example programs into 1 program.
I made a mistake because the filter sim pitch and the filter's sim roll variable value are incremented / changed per measurement.
Why is the value of "filter pitch" increasing?