Search found 40 matches

by Henk
Sun Dec 20, 2015 7:25 pm
Forum: Flowcode V4
Topic: Flowcode 4.5
Replies: 1
Views: 9268

Flowcode 4.5

Hello Ben Rowland,
I had to re-install Flowcode because my hard drive failed. I installed flowcode 4.5. I have the install code that's ok, but the activation code does not seem to be good. The code is not worthy. What should I do?

Greetings Henk Middendorp.
by Henk
Thu Dec 10, 2015 7:35 pm
Forum: Flowcode V4
Topic: Pic 18f4550 and USB
Replies: 7
Views: 13912

Re: Pic 18f4550 and USB

Hi All, I configured the 18F4550 chip expert in the config screen . If I make a simple flowchart with a LED on output rb0 and I send it to the chip then led the fire . But once I got the USB icon in the flowchart place and I send it to the chip the led is not burning . What is wrong? Greetings Henk ...
by Henk
Thu Nov 26, 2015 10:06 pm
Forum: Flowcode V4
Topic: Pic 18f4550 and USB
Replies: 7
Views: 13912

Re: Pic 18f4550 and USB

Hello Medelec35 ,
Thank you for your response.
I have found the error my program was too big so that the error arose .

I have another question,
How can I tell if there is data traffic on the lines D + and D-. Perhaps through LEDs in the D + and D- line ?
Or is there another solution?

Henk.
by Henk
Wed Nov 25, 2015 8:10 pm
Forum: Flowcode V4
Topic: Pic 18f4550 and USB
Replies: 7
Views: 13912

Re: Pic 18f4550 and USB

Hello Ben. I use flowcode 4.5 and a pic 18F4550 and I like the USB icon in my flowchart do I get this error . What I try nothing helps. What should I do? Below you see the error? le name: D:\Weerstation via WIFI\4550 1 keer proberen.c Generated by: Flowcode v4.5.18.74 Date: Wednesday, November 25, 2...
by Henk
Mon Nov 23, 2015 7:55 pm
Forum: Flowcode V4
Topic: Pic 18f4550 and USB
Replies: 7
Views: 13912

Re: Pic 18f4550 and USB

Hello Henk, You have to configure the 18F chips using the expert mode. if I want to send it to the pic I get a foutmeling Not sure what you mean here. Can you explain further. Hi Ben, thanks for your comment. I first try to configure it in Expert config screen . Can I find examples somewere? Greeti...
by Henk
Sun Nov 22, 2015 4:51 pm
Forum: Flowcode V4
Topic: Pic 18f4550 and USB
Replies: 7
Views: 13912

Pic 18f4550 and USB

Hi all, I use Flowcode 4.5 and when I do I choose Flowcode open a new Pic 18F4550 and I make a short program with the block USB serial and if I want to send it to the pic I get a foutmeling . Then there is upgrade your source boost. Then I would have to surf to www.sourceboost.com to upgrade. Who ca...
by Henk
Tue Nov 17, 2015 7:55 pm
Forum: Flowcode V4
Topic: USB with a pic18f4550
Replies: 2
Views: 9202

Re: USB with a pic18f4550

Benj wrote:Hello Henk,

Flowcode 6 supports USB communications using the simulation. Previous versions of Flowcode do not support this functionality.

Thanks for you information.
by Henk
Mon Nov 16, 2015 8:07 pm
Forum: Flowcode V4
Topic: USB with a pic18f4550
Replies: 2
Views: 9202

USB with a pic18f4550

Hello everybody,

How can I make visible the value of the usb while simulating in Flowcode 4.5
What part is that?
I use a Pic 18f4550.

Greetings by Henk Middendorp.
by Henk
Mon Nov 09, 2015 7:51 pm
Forum: Flowcode V4
Topic: USB driver
Replies: 1
Views: 8486

USB driver

Hello all
I 'm looking for a USB driver for the PIC18F4550 .
I want to make a conection between the PIC 18F4550 and a PC.
That means a usb program in the pic?, but also in the PC I think.
Where can i find it?

Greetings Henk Middendorp.
by Henk
Sun Nov 08, 2015 5:00 pm
Forum: Flowcode V2 & V3
Topic: Let Us Know What You Are Doing With Flowcode
Replies: 42
Views: 86374

Re: Let Us Know What You Are Doing With Flowcode

Hello, I make e wetherstation and I use a PIC 16f877a. I have a anemometer, a wind direction, a temperature, a barometric pressure. I use a pic 16f877a en I make a connection between the PIC and the computer and than I put it on wifi so that I Can see wetherstation on a samsung tablet in my livingro...
by Henk
Sat Oct 31, 2015 5:01 pm
Forum: E-blocks
Topic: E block EB-006-00-4
Replies: 2
Views: 5319

Re: E block EB-006-00-4

Hello Jack,

I have the driver installed and the bord is working perfect.

Thank you.

Greetins Henk.
by Henk
Fri Oct 30, 2015 7:48 pm
Forum: E-blocks
Topic: E block EB-006-00-4
Replies: 2
Views: 5319

E block EB-006-00-4

Hallo, Sinds een paar weken heb ik windows 10, maar nu kan ik geen programma's meer vanaf Flowcode V4.3 via mijn programeerblock(EB-006-00-4) naar de Pic toe sturen. Als ik het probeer dan zegt Flowcode USB cable is not connected terwijl de kabel er gewoon in zit. Kan ik ergens een USB driver downlo...
by Henk
Fri May 21, 2010 8:03 pm
Forum: Flowcode V4
Topic: USB programmer bord
Replies: 2
Views: 2368

Re: USB programmer bord

Hi Ben,
I have two computers and one of them is about 6 years old and on that one I must install the USB drivers extra.
It is not necessary to install the USB drivers on my new computer, if I install PPP 3.9 the USB driver installs itself.
Everything is fine now.
Kind regards,
Henk Middendorp
by Henk
Thu May 20, 2010 7:15 pm
Forum: Flowcode V4
Topic: USB programmer bord
Replies: 2
Views: 2368

USB programmer bord

Hi there,

Flowcode V4 and PPP3, 9 is installed on my computer with windows7.
But not the USB programmer board.
I have try everything but nothing works.
So What Can I Do?

Kind regards,
Henk Middendorp.
by Henk
Tue Jan 19, 2010 8:06 pm
Forum: Flowcode V4
Topic: V 3.xx and V4.2
Replies: 7
Views: 4906

Re: V 3.xx and V4.2

Hello, I have created this program with V3.xx I want to load this programm with V4.2 I get an error immediately. Flow V4.2 Code says> Connection and properties for the following components are failed to load : LedSeg4. The following macro wil be ignored because is no longer used ADC0:: sample ADC. I...
by Henk
Tue Jan 19, 2010 11:59 am
Forum: Flowcode V4
Topic: V 3.xx and V4.2
Replies: 7
Views: 4906

Re: V 3.xx and V4.2

Yes, I really can not.
Programs that have been made in V3.xx in V4.2 must be read normally.

Henk
by Henk
Mon Jan 18, 2010 8:44 pm
Forum: Flowcode V4
Topic: V 3.xx and V4.2
Replies: 7
Views: 4906

V 3.xx and V4.2

Gentlemen,

I am well pleased Flow Code V4.2.
But if I want to load programs with V4.2 I have great problems with the macros.
Many of the macros do not work and I need to export them first and then import then it just right.
That can not be what I hope.

Greetings Henk.
by Henk
Mon Jun 08, 2009 5:55 pm
Forum: Flowcode V4
Topic: Flowcode V4
Replies: 42
Views: 26396

Flowcode V4

Hello there,

I have just download Flowcode V4.
Now the program aks for a key.
I have a key but when i fill in than de program says the key is not valid.
Can you tell me what the problem is.
I use the license for Flowcode V3.

Henk.
by Henk
Wed Feb 04, 2009 6:27 pm
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

Re: C-code

Hello, Last week I had a question which I asked whether it was possible for the bar at the bottom of the 9 to be seen. And whether it was possible that I could see a minus sign as the temperature of my temperature display is below 0. That was not so easy to solve as I thought. But we have still foun...
by Henk
Fri Jan 30, 2009 5:13 pm
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

Re: C-code

Thanks you for your time I wait voor Flowcode V4

Henk.
by Henk
Fri Jan 30, 2009 4:01 pm
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

Re: C-code

Hi Steve, Yes it is true that I have also tried to led7seg1.c file, but here I see no change on my USB test board. now I must wait til next upgrade from Flowcode Thank you Steve! Then I have another question, I have a temperature sensor built with Flowcode. De temperature go from -30 to +50. How can...
by Henk
Thu Jan 29, 2009 8:40 pm
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

Re: C-code

Hello Ben, I've done everything you said. I went to c: \ Program Files \ Matrix Multimedia \ Flow Code V3 \ components went and got the file opened in notepad led7seg4_code changes Done as you have said. I have tried //set pattern array for the display rom char* cSegmentArray = {%c, %d, %e, %f, %g, ...
by Henk
Wed Jan 28, 2009 9:07 pm
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

Re: C-code

Hello Ben, I tried but I see no change in the 9 when I send my program to my USB steering board. I have tried 0x90 0x88 and 0x98. I have do all de things what you said but Nothing works. Greetings Henk Hell0 Yes this is possible. Open your Flowcode components directory located in C:\Program Files\Ma...
by Henk
Tue Jan 27, 2009 9:01 am
Forum: Flowcode V2 & V3
Topic: C-code
Replies: 10
Views: 6974

C-code

Good morning Gentlemen,

When I Flow Code leddisplay's use and I want to see a 9 I would also like the dash (segmentD) want to see at the bottom of the tail.
Is that possible?

Groeten Henk.
by Henk
Mon Dec 29, 2008 6:28 pm
Forum: Flowcode V2 & V3
Topic: A four digits leddisplay
Replies: 0
Views: 3433

A four digits leddisplay

Hello Benj,

In Flow Code is a 4-digit LED present as a macro.
I wonder whether there is a code for the 4-digit leddisplay.
If so, is it possible to send that code to me.

Henk.