Search found 11 matches
- Sun Oct 21, 2007 2:24 pm
- Forum: Flowcode V2 & V3
- Topic: Interrupt Handling ?!
- Replies: 11
- Views: 9453
Hi all, I was testing again with the custom interrupts; I cant seem to get the receive interrupt working. I geuss the custom specific interrupt name should be the "GCC name" eg. USART_RX_vect the specific enable code should be UCSRB |= _BV(RXCIE); . Is this correct, probably not... What is the corre...
- Fri Oct 19, 2007 4:19 pm
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
Hi again Steve, I tried another homebrew programmer Launching the programmer... C:\Program Files\Matrix Multimedia\Flowcode_AVR\Tools\MX_bats\avrc.bat m8 bascom lpt1 "SimpleLed.hex" 0 2 209 -1 -1 C:\Documents and Settings\Koen Kempeneers\Mijn Documenten\Flowcode_AVR>"C:\PROGRA~1\MATRIX~1\FLOWCO~2\To...
- Fri Oct 19, 2007 3:36 pm
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
Hi Steve, The new release stills tries to read fusedata when programming, that is not supported by most bootloaders. C:\Documents and Settings\Koen Kempeneers\Mijn Documenten\Flowcode_AVR>"C:\PROGRA~1\MATRIX~1\FLOWCO~2\Tools\MX_bats\..\AVRDUDEusb\avrdude.exe" -p m8 -P COM1 -c butterfly -U flash:w:"S...
- Thu Oct 18, 2007 11:42 am
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
Hi again Steve, I'm still testing te interface with AVRDUDE, by now i just use; @SET AVRDUDEcmd="C:\Program Files\Matrix Multimedia\Flowcode_AVR\Tools\AVRDUDEusb\avrdude.exe" -p %1 -c %2 -P %3 -F -e -U flash:w:%4:a -U flash:v:%4:a %AVRDUDEcmd% The program is called with; %a butterfly COM1 "%f.hex" S...
- Tue Oct 16, 2007 3:01 pm
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
- Tue Oct 16, 2007 2:58 pm
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
Is it anything like; @ SET Fuse1= @ SET Fuse2= @ SET Fuse3= SET AVRDUDEcmd="%~dp0..\AVRDUDEusb\avrdude.exe" -p %1 -c %2 -P %3 -F -u -U flash:w:%4 @ IF NOT "%5"=="-1" SET Fuse1=-U hfuse:w:%5:m @ IF NOT "%6"=="-1" SET Fuse2=-U lfuse:w:%6:m @ IF NOT "%7"=="-1" SET Fuse3=-U efuse:w:%7:m %AVRDUDEcmd% %Fu...
- Tue Oct 16, 2007 1:38 pm
- Forum: Flowcode V2 & V3
- Topic: Programmer settings
- Replies: 10
- Views: 10665
- Mon Oct 15, 2007 9:43 am
- Forum: Flowcode V2 & V3
- Topic: Interrupt Handling ?!
- Replies: 11
- Views: 9453
Interrupt Handling ?!
Hi all, I've written a small program using the PWM and the UART macro's. Running on M8, i can't seem to get the interrupt system up and running, //NOTE: failed to add interrupt [RXComplete] (IntHandlerCode is blank) Is the interrupt system not operational yet? Remember that the interrupt system on a...
- Wed Sep 12, 2007 3:20 pm
- Forum: Flowcode V2 & V3
- Topic: run time
- Replies: 2
- Views: 2984
Hi Wolfgang, All depends on the kind of application your writing. If you wrote a small calculator 8ms would be an acceptable cycle time. For a PLC 8ms is quitte fast. I've written applications that keep it under 100us at 12Mhz clock, i've written applications that take up to 500ms worst case cycle. ...
- Sun Sep 09, 2007 3:48 pm
- Forum: Formula Flowcode
- Topic: Chargement
- Replies: 7
- Views: 10123
- Sat Sep 08, 2007 3:07 pm
- Forum: Flowcode V2 & V3
- Topic: Flowcode for Microcontrollers other then PICs
- Replies: 8
- Views: 12251