Matrix user forums

Hello Ben,

I understand the cause of the problem.
Thank you again for the answer.

Lagoda

Hi Ben,

Thanks for the reply.

I'm sorry that the simulation does not provide a reliable result in this case.
For 100 us, 10us, and 1us delay, the pulse width measured on the RC0 pin is 0.53us according to the simulation.
Is this the same reason?

Best Regards,

Lagoda

Hi Everyone,
I found this bug in Flowcode 7.3.0.6 during simulation.
I think the pictures say everything from the problem.

Best Regards,
Lagoda

OK!
Thank you very much.

Hello, Ben and Leigh, I tested my FlowKit2 on the weekend. Depending on the version of the Flowcode I found the differences. No matter what kind of operating system or hardware configuration I tried it on. The DIGITAL part of ICT functionality works well in Flowcode version 7.2.1.4. (Although I did ...

Hi Leigh, Thank you for quick responding to the problem. I tried to use FlowKit 2 on several machines, 1. on a laptop under WINDOWS 7 with Flowcode 7.3.0.6 + Patch 2. on a gamer machine under WINDOWS 10 under a newly installed Flowcode 7.3.0.6 + Patch 3. and a medium-sized desktop on WINDOWS 7 opera...

Hi QMESAR, Would you be so kind to tell me, What was the solution to the problem? I also have a FlowKit2 board since a year. So far it was in the desk drawer, I haven't used it. Now I want to debug with it , but the ICD module don't working. Every information interesting for me in this topic, becaus...

Joy and happiness!!!

The improved version that you have created works perfectly.

The UART bridge now works in my circuitboard, but I do not know what it was.

Thanks again for your help.

Lagoda

Hi Ben, Works well with the test program. :) I have created an UART bridge on the target panel between the GSM module and an RS232 interface with UART RX interrupt. Unfortunately, it does not work in this program. Maybe I did something wrong. I'll check it out. Thanks for the quick fix. I'll let you...

Hi Ben, Now there is a problem with UART interrupt. When a byte is loaded into RX FIFO it does not cause interrupt. I used the Configure setting, what Stefan Erni suggested. (Boot ISA Selection=Boot code and Exception code is MIPS32) I tried to debugging with different settings of SFR (priority leve...

Hi Ben,

Super!

I tried just a few pins, but they worked.

Thank you very much.

Lagoda

Hi Ben,

Hurray!

The repaired version is works perfectly.

Thanks for your quick help.

Lagoda

Hi Ben, Now there is a problem with the Modbus Master component. It would be good if you could help me. While the Modbus Master sending a data packet to the Slave, during the DIR-pin switch to receiving. On the RX pin also shows a 110ns long pulse, but I do not know why. (Probably due it is to switc...

Hi Stefan,

Thank you very much for the informations.
The knowledge that you share will be useful to me as well.
I'm glad you work with this MCU family and there I'm not alone on the forum with the problems.

I'm begining of the work , now testing the peripherals.

Best Regards,
Lagoda

:D I found the cause of the mistake! The Rx input of the UART6 I set in the Flowcode to the RD5 pin, but in fact the RB6 was activating. When I checked the content of the U6RXR register I found 0x05 instead of 0x06. I corrected the value to 0x06 in source C and then it worked. Unfortunately I do not...

Hello, I would like to ask for help. If I set the UART to "Channel 6" in the attached program, it can not receive the characters. If I set channel of UART to "Software", it works perfectly. The external clock of the MCU is 14.7456 MHz. I also attached the clock settings. ( I tested the UART transmit...

The PIC32MZ device only supports both edges as part of the IOC interrupt, it is a limitation of the silicon not Flowcode.

Oops!

This avoided my attention. I'm sorry.

I hope this MCU isn't will cause more surprises for me.

Thank you very much.

Best Regards,

Lagoda

Hi Ben, I checked what you recommended. In this example, you can set any type of edge. (color of the pin may be green, red, gray or white) And I opened a new project. If I set the type of target MCU to PIC32MZ2048EFM144 then you can activate the interrupt on both edges only. (The color of the pin ma...

Hi All, I would like to use a PIC32MZ Series MCU. I wanted to use an external interrupt, but I could not to interpret what I see in the "Interrupt Proprties" window. How can I to setup the masks? I've also tried the "Select pin (s)" button, but every pin of this port is active at both edges by defau...

Hi Igor,

I think the J7 connector is the right one, if you use PICKIT3.

Best Regards,

Lagoda

Hi Ricardo, I think you should use more samples for the decision and have to find local minimum and maximum. It should be considered whether the actual sample value is smaller or larger than the previous samples. For example, if the value of samples was growing for a time, but value of three samples...

And it works well !!!

Thank you very much!

Lagoda

Hi Ben,

Thank you for your help.

Unfortunately, the problem remains.

If i set the reference VDD then in the line 626 is: FC_CAL_ADC_Enable(3, 3, 0, 40);
If i set the reference Vref+ then in the line 626 is: FC_CAL_ADC_Enable(3, 3, 1, 40);

Best Regards,

Lagoda