Matrix user forums

Hi Rudi, It could be that your clock speed is incorrect as this would cause the unknown device error. Change the device config so 1s delays are equal to 1s with the clock speed set to 32000000 and then the USB should fire up correctly. Ok Benj, i was deeper in the code and ... i am sorry. i can not...

Hi Benj - my latain is finnished ;-) ;-) ;-) I will test arround again next times with more tests.. whats going with this PIC24 or Baudrate ;-) ;-) ? ..i have added pics.. Thank you for your great Service!!! PS. I added original Wifi Webserver Code too. Also the Circuit / Shema of the Board. Best wi...

Hello Rudi, Please can you try the attached FCD for me. Hopefully it should work correctly for you. 24FJ256GB106.fcdx 24FJ128GB106.fcdx You need to get the config and project options clock speed setup correctly so that 1s delays = 1 second delays on the hardware. This means the clock and config is ...

Sorry For Push I test just in Time same PIC but i have at this Board a 20 MHz Crystal.. Clk Speed 8000000Hz Oscillator input divided by 5 ( 20 MHz ) Config3: 0xFFFF Config2: 0x43BE Config1: 0x3E7F I have then set all to Channel 2 , Baudrate 9600 works.. I have change to Channel 3 ( same baud ... sam...

Hi

i do not know why but USB Serial or USB HID or USB Slave is not going on.
I make a simple test with USB Serial i attached.
In Windows a New Hardware will found but do not install the driver " unknown Device "
I have Simple Project attached.
Any Idea?
Thank You!
Best wishes!

Rudi

Hi for more USB Compos i start with USB MIDI ... i have found a lot of Descriptor at Microchip Examples... i modify a little for MIDI USB .. The Strings can be change if someone need this... .. Now i will start to "learn" in Flowcode how this USB i can create as a USB Compo for USB MIDI.. for later ...

Hi,

can u pls check this:
PIC24FJ256GB106

I want to set INPUT sw to PORTB.12 - PORTB.15
example
PORTB SINGLE Bit at PORTB12..PORTB15
ist this PORTB_H 4 -7 ?
..

..in Entry Mask "Use Masing" the same..

Thank you!

Best wishes!

Rudi

Sorry for Push Benj, i have test with setting a config bit... normally the Board is 12MHz .. i have test with set the Bit at Bit 28-30 .. Oscillator input divided by 6 ( 24 MHz input ) The Hw Uart i set to 57600 and in Terminal too. Now the Baudrate are corect - but the delay 1s in programm is doubl...

Hi Rudi, Please can you try this fix for me, Please the attached file below into your "C:\Program Files (x86)\Flowcode 6\CAL" folder and try re-compiling using a hardware channel. The problem seems to be related to the device clock speed which should be dividing by 2 to obtain the correct hardware ...

Input: Switch_array_push and Switch_array_Slide Can not set Custom Pins Hi Rudy, Good spot - thanks for your report. In this case, it is the tooltips which are incorrect. We found that teachers were reporting that the old switch array was confusing for their younger students due to the many options...

Hi I have tested in RS232 and First Time a little "Cosmetic" playing with me.. If i add a RS232 Compo the Scope will show automatic . If i close the Scope or deactivate in View or make it Auto Hide and then make Change in Properties example Baudrate, the Scope again allways popup... --- Input: Switc...

hallo liebe Flowcode Gemeinde, Mein Problem besteht im Lesen der ankommenden Daten. Ich verstehe die 2 Macros 2ReceiveMIDI" und "ReadData" nicht. Was macht "ReceiveMIDI"? Was ist das "cTimeout(Byte)"? Was macht "ReadData"? Was ist das "cIdx(Byte)"? Hi Philipp, Midi Format ist klar? Also kurz: Statu...

Hi i try to get this run with HW UART but i think i make false or the Uart will make fun to me...;-) or i try a function that not gives.. If i try the RS232 with Channel example Channel 2.. the Tx and Rx connections will be grey and i can make Tx Remap Rx Remap so i set this to PortG.6 and PortG.7.....

Hi only a question: is it possible example in main program to catch a local variable from a macro like this flowchart main...calc....calc2 in main mainglobal=calc.local + calc2.local and / or is it possible in a macro to catch a localvariable from main / macro like calclocal = main.local + calc2.loc...

Hi Rudi, Would the peek function just look at the pending next get output or would you want it to be able to look at any value in the buffer? Hi Benj, i hope my translate is ok.. ( "at the pending next get output" google translate this not 100 procent clear.. ) but i will ask to your ask for better...

Hi i make with Pic18F2550 and a wifi shield connect to Internet and put data to my private homepage... You can connect a Wifi rs232 shield like this to the uart. simple connect Wifi Rx to Tx Uart ( Soft or HW ) Wifi Tx to Rx Uart Soft or HW ) make Sure GND and VCC is on Wifi Shiled same like Pic ( 5...

Benj wrote:Here you go, flush function simply resets the start and end pointers.

Great!!!! Benj,

thank you! ...
ll
ok..
only a ask ok )


how look circular buffer wíth "peek" function )))..
( without ´taken ( del) from the buffer...
any idea?

)
yeah!

Rudi

Hi
is there a way to make a "flush" to the buffer?
Thank you!
Rudi


Edit...
And a way to make "Peek" a byte
))

Hi Jonny All the best on your future life. You will be sorely missed here. Let yourself once in a while here. Benj, you and certainly all the others in the Matrix Team do a great job! We learn a lot from Matrix Team. Carry on as before. You will certainly go very far. I am sure. All the best Best wi...

Hello, Hmm I can't figure out a reason why timer 0 would not be firing on this device. Looking at the C code produced it all looks fine. I have just tested on a 18F4455 which is the same device family and it is working fine. Comparing the C code it's identical so I'm a bit stumped? Could you use ti...

Hi Rudi, I've added a timer interrupt and circular buffer component to take care of the USB comms and the MIDI transmission. There might still be problems when receiving data while transmitting so let me know how you get on. "Where is the 1000 Thanks Button ?" ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ;-) Hi B...

Hi i try a simple i have try in RS232 to receive MIDI Data.. but the Bug in 0 Bytes was in RS232 so i try it with MIDI_Compo.. i will read MIDI Data in in this example with MIDI Compo. ( if RS232 better go - i will change to it ) I have a MIDI Shield at UART or Software UART - all two i try... Midi_...

Thanks to the MATRIX Team! ========================= You hard at work 24/7 ! Just in Time i download the Candidate, i will test it too for my founds Best wishes from Germany ;-) Rudi ;-)^ 1) Edit: March 27th-14 I have tested in RS232 and First Time a little "Cosmetic" playing with me.. If i add a RS...

http://wwww.matrixmultimedia.com/mmforums/viewtopic.php?f=2&p=42711#p42711 Sorry Benj for this OT Theme but i work in this at FC6 with a simple Test ..and i would test a option for me for a better understanding. Benj, is there a way to modify the MIDI Compo in FC6 same way? If i right click in FC6 a...

Hello Rudi, is the USB OTG supported in FC6 or is there a way to make a USB OTG Component? ...but yes it is possible to create it in Flowcode v6 using the component creation interface.....The demo code provided by Microchip will work with the compiler but you will have to do a bit of hacking around...