Matrix user forums

Hello! Steve
good afternoon

The Script Error pops every time i try to save the project, i read above post so not worried just want to put to notice.

Abhi

Hello! Ben good morning Many many thanks for checking and the new suggestions, i implement the new changes now in my chart. Yes i have checked the difference between both the speeds, program works at a high speed once it leaves the macro i.e the C calculation box from Check_SDCard_Status. Thank you ...

Hello! Ben good morning Yes, i anticipated that probability yesterday about the availability/unavailability of the prescaler, so i took a chance of trying your suggestion in your previous post I also wonder if it is possible to start at a slower speed, startup the SD card and then switch to a faster...

Hello! Oderlando

Are you facing the problem in simulation or at actual, just for knowledge the chart works well in simulation for me, i could see the font size changing after the delay, i am not able to check on real hardware.

Abhi

Hello! Ben
Good morning

Any good news for me, waiting desperately for your answer.

Thank you.

Abhi

Hello! Ben good afternoon Thanks for your reply, i am using PIC18F46K22. Oh! i never imagined that, about exposing the options of available prescalers on device/chip, if i have not mistaken i also tried using PIC18F26K22 and PIC18F26K42, but never saw any other option other then Fosc/4,16,64 Ben if ...

Hello! I want to update my recent progress on FAT component, i am able to initialize and run the component using 8MHz+PLL=32MHz, with Initial Prescaler=foc/64 (500KHz, little more then mentioned 400KHz) and High Speed Prescaler=foc/4 Is there any last hope to run the PIC micro at 16MHz+PLL=64MHz, be...

Hi! Martin

Not only the LED blink every second my calculation box now calculate the average exactly after 1 minute without fail.

And regarding the soldering to the pin 3, it was not a big trouble.

Cheers Martin, have a pleasant evening.

Abhi

Hello! Martin Humbly thank you for your valuable input, your suggestion worked like a "Piece of Cake". As you instructed i manage to take the pin 3 of the chip to one of the interrupt pin on my chip, the RTC was already powered, i configured the SQWandINTcontrol Macro at the beginning of the main lo...

Hi! Martin good afternoon Thank you to share your views, may i request you to share some example if possible, or may be a link to some post, unfortunately i did not find any on that topic. I have observed one more thing with my RTC module, apart from Vcc, Gnd, SDA, SCK there is no other pin availabl...

Hello! I am trying to save some readings after every 1 second, i am using DS3231 RTC for time keeping, i tried to do something similar from below post of Ben, but unfortunately it is not working as expected. https://www.matrixtsl.com/mmforums/viewtopic.php?p=98927#p98927 I want to note and add the r...

Hello! Martin Once again thank you for your help for the moving average example, but to be honest with you i used your other example again (Analog Filter) it works fantastic for this application, thank you for that example too. Hello! Peter As you said i have changed all the variables to Long and no...

Hello! Martin Hello! Peter
good afternoon

Kindly excuse to speak my mind but what a profound feeling of friendship, thank you both very much for your answers. I check both the options and keep posted with the result.

Thank you again.

Abhi

Hello! Martin good morning So nice of you to post the example, thank you. May i request you to answer one doubt, i notice the ADC value receiving from the pot is 1023 as the resolution is of 10Bit in the example chip, on contrary i am using the component MCP3421 which has got 18Bit resolution, in th...

Hello! I am trying to stable the reading of ADC value, is it possible to put some light if someone has already done in the past, the ADC is of 18Bit how to do the calculation using Moving Average method. I read very few post on this topic, most of them are from V4, it will be great if someone could ...

Hello! Enrique Kindly excuse i am not aware of the setup of your project, this is a suggestion if it is possible for you to use a magnetic reed switch then you have a probability of setting the vicinity of operation of the reed switch by placing the magnet close or far as per your requirement, may b...

Hello! Peter https://www.flowcodexchange.com/post/ads1115-adc-16-bit-with-pga-use-in-flowcode Best explanation, now i am so eager to receive the module and test it as soon as possible, once again many thanks for this much needed component, cheers.... Like Martin (medelec35) “All's well that ends wel...

Hi! Martin Finally i could place the component, now it is available, thank you Martin. I was addressing QMESAR as Peter, i did not knew it was Martin, reality is Martin's are Savior :D (valued contributors) Once again thank you to get me out of this, may be i will bother you tomorrow :twisted: i am ...

Hi! Martin Kindly excuse to bother you again, but i was not successful. I tried both ways, to place the single file ADS1115.fcpx in the V8-Components folder and also by assigning the path in the global view like you instructed, i think i am doing something wrong, or this component is not for FC V8, ...

Hi! Martin good afternoon Believe me yesterday in hurry and worry i just post my problem/doubt without doing any investigation, today afternoon (India time) i found the post of Peter and the 16Bit ADC component, i just downloaded from his website. This is my first time to install the component so as...

Hello! May i request, if someone can help me with using a 16Bit ADC chip, i have reached a dead end, i tried using 12Bit internal ADC of PIC18F26K42 chip but unfortunately i am not getting the reading as expected as the change is very very small at the input. The only component available in FC8 is A...

Hello! Ben good afternoon For efficiency the flush command simply resets the read and write pointers, the contents of the buffer are unaffected so this is probably what you are seeing. May i request you if it is possible and the upgrade of component allows, to add one more option/command for this co...

Hello! Ben good afternoon Thanks to revert back. I am using FC8, yes as you said i tried all the available options but without success, it only initialize at 16MHz without PLL, once i enable the PLL it stops responding or i can say the card writer do not initialize so nothing happens further. Just i...

Hello!

Any suggestions from the experts, team members regarding my previous post, or i am asking something wrong or not possible so i could think for another option.

Thank you.

Abhi

Hello! George good morning Hope that helps and someone else having the same issue. Indeed your post and example was very helpful to me, thank you for that. Now i am facing one more problem, when i run the flow chart using 16MHz crystal then everything works fine as per your present chart, but in my ...