HI
If you buy the pro licence then all the components are fully activated
Regards
Dazz
Search found 966 matches
- Wed Nov 19, 2014 10:16 am
- Forum: Flowcode V6
- Topic: It's SPI Communications active?
- Replies: 11
- Views: 6733
- Sat Oct 18, 2014 2:46 pm
- Forum: General Programming
- Topic: Flash Memory Question
- Replies: 5
- Views: 4497
Re: Flash Memory Question
Hi Benj
Re Win8, win 8 doesnt defrag ssd's it doesit another way called trim only takes a few seconds to do.
Regards
DAzz
Re Win8, win 8 doesnt defrag ssd's it doesit another way called trim only takes a few seconds to do.
Regards
DAzz
- Fri Oct 17, 2014 1:33 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
hi
i thought your fcd may have been corrupted as it appeared to point at a different programmer, have you got a link to where you bought your mega from,as if its not too expensive i may order one in a few weeks and try it here, as an aside my uno's use the ch30 drivers and work fine
Regards
Dazz
i thought your fcd may have been corrupted as it appeared to point at a different programmer, have you got a link to where you bought your mega from,as if its not too expensive i may order one in a few weeks and try it here, as an aside my uno's use the ch30 drivers and work fine
Regards
Dazz
- Thu Oct 16, 2014 8:30 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi
the 2 bat files are identical to mine, can you place the attached fcd in yor avr fcd folder and try again, its a long shot but it might work
Regards
Dazz
the 2 bat files are identical to mine, can you place the attached fcd in yor avr fcd folder and try again, its a long shot but it might work
Regards
Dazz
- Thu Oct 16, 2014 3:57 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi Jorgen One thing that stands out immediately is as below Mine C:\Program Files (x86)\Flowcode 6\compilers\avr\batchfiles\avrc_arduinoB.bat m2560 stk500v2 com6 115200 "Flowcode1.hex" Jorgen's C:\Program Files\Flowcode 6\compilers\avr\batchfiles\avrc_arduinoA.bat m2560 wiring com8 115200 "MegaSlet....
- Wed Oct 15, 2014 2:54 pm
- Forum: Flowcode V5
- Topic: GUIDE: Arduino programming via USB
- Replies: 20
- Views: 50444
Re: GUIDE: Arduino programming via USB
Hi steve
read this page, its semi automatic
http://www.matrixtsl.com/mmforums/viewt ... 4&start=50
Regards
Dazz
read this page, its semi automatic
http://www.matrixtsl.com/mmforums/viewt ... 4&start=50
Regards
Dazz
- Tue Oct 14, 2014 5:40 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi
try this see attached pic
Regards
Dazz
try this see attached pic
Regards
Dazz
- Tue Oct 14, 2014 2:01 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi
It should be automatic, but i have to reset my mega before it programs, wsee attached pic, when it gets to that point hold the mega reset buton and release it as soon as you press ok
Regards
Dazz
It should be automatic, but i have to reset my mega before it programs, wsee attached pic, when it gets to that point hold the mega reset buton and release it as soon as you press ok
Regards
Dazz
- Tue Oct 14, 2014 12:52 pm
- Forum: General Programming
- Topic: fc v6 pic error code 255
- Replies: 5
- Views: 5687
Re: fc v6 pic error code 255
Hi Kon
Have a look in the avast virus vault, as on my laptop it stopped compiling, because avast was trying to be clever. if its in there click on restore and add to exeptions(something like that)
Regards
DAzz
Have a look in the avast virus vault, as on my laptop it stopped compiling, because avast was trying to be clever. if its in there click on restore and add to exeptions(something like that)
Regards
DAzz
- Tue Oct 14, 2014 12:49 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi
i can program mine but i have to reset it just before it times out, i think it may need a reset putting into the parammeters, how i dont know
try clicking build and you can select the arduino in a box on the right make sure it corresponds with the port you are using and try again#
Regards
Dazz
i can program mine but i have to reset it just before it times out, i think it may need a reset putting into the parammeters, how i dont know
try clicking build and you can select the arduino in a box on the right make sure it corresponds with the port you are using and try again#
Regards
Dazz
- Tue Oct 14, 2014 10:22 am
- Forum: Feature requests
- Topic: EB088 support
- Replies: 1
- Views: 2606
EB088 support
Hi Guys
Any chance of a component for the EB088 Eblock cap touch board
Regards
Dazz
Any chance of a component for the EB088 Eblock cap touch board
Regards
Dazz
- Tue Oct 14, 2014 10:16 am
- Forum: Flowcode V6
- Topic: PICKIT 2
- Replies: 4
- Views: 3767
Re: PICKIT 2
HI Fella
try updating the firmware in the pickit2, as you may have different file versions, i had to do this a while back
Regards
Dazz
try updating the firmware in the pickit2, as you may have different file versions, i had to do this a while back
Regards
Dazz
- Mon Oct 13, 2014 2:24 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi Monie
select the default programmer in V6.1 set it to default and try again, also when you uninstalled did you also remove the flowcode folder on your c drive as this will keep the old compiler settings etc
Regards
Dazz
select the default programmer in V6.1 set it to default and try again, also when you uninstalled did you also remove the flowcode folder on your c drive as this will keep the old compiler settings etc
Regards
Dazz
- Sun Oct 12, 2014 5:48 pm
- Forum: Flowcode V6
- Topic: Interrupt Arduino Uno
- Replies: 16
- Views: 9844
Re: Interrupt Arduino Uno
Hi jorgen
i got my sums wrong it should have been 31250 i think, was tired yesterdat sorry
Regards
Dazz
i got my sums wrong it should have been 31250 i think, was tired yesterdat sorry
Regards
Dazz
- Sun Oct 12, 2014 5:46 pm
- Forum: Flowcode V6
- Topic: Arduino Programming In Flowcode v6
- Replies: 116
- Views: 231816
Re: Arduino Programming In Flowcode v6
Hi Monie
works here, try this click on build and there should be a drop down box called programmer port select your port then compile to chip,
Regards
Dazz
works here, try this click on build and there should be a drop down box called programmer port select your port then compile to chip,
Regards
Dazz
- Sun Oct 12, 2014 12:31 pm
- Forum: Flowcode V6
- Topic: adc voltage sample program
- Replies: 13
- Views: 9136
Re: adc voltage sample program
Hi
ran your chart and had the following results, are you using V6.1 as i think other versions had an adc issue on the arduino 2560. if not download v6.1 and try again
Regards
Dazz
ran your chart and had the following results, are you using V6.1 as i think other versions had an adc issue on the arduino 2560. if not download v6.1 and try again
Regards
Dazz
- Sun Oct 12, 2014 12:12 pm
- Forum: Flowcode V6
- Topic: Interrupt Arduino Uno
- Replies: 16
- Views: 9844
Re: Interrupt Arduino Uno
Hi
All i know is if you place a delay in an interupt it will cause issues like you are getting, which is why its better to use a count like in the chart i did,
hope that helps
Regards
Dazz
All i know is if you place a delay in an interupt it will cause issues like you are getting, which is why its better to use a count like in the chart i did,
hope that helps
Regards
Dazz
- Sat Oct 11, 2014 8:32 pm
- Forum: Flowcode V6
- Topic: adc voltage sample program
- Replies: 13
- Views: 9136
Re: adc voltage sample program
Hi
Run the sim and dragf the speed slider to the right a bit this will then show all the variables, by doing this tension was displaying
Regards
Dazz
Run the sim and dragf the speed slider to the right a bit this will then show all the variables, by doing this tension was displaying
Regards
Dazz
- Sat Oct 11, 2014 8:10 pm
- Forum: Flowcode V6
- Topic: ECIO40P16 compile errors and a ton of warnings
- Replies: 13
- Views: 8128
Re: ECIO40P16 compile errors and a ton of warnings
Hi Fella
Can you post your flowchart as it may allow someone to spot the error
Regards
Dazz
Can you post your flowchart as it may allow someone to spot the error
Regards
Dazz
- Sat Oct 11, 2014 8:08 pm
- Forum: Flowcode V6
- Topic: Interrupt Arduino Uno
- Replies: 16
- Views: 9844
Re: Interrupt Arduino Uno
Hi
Try the attached chart, basically at 16mhz a count of 31(ish) will = 1/2 sec , so one int triggered ,it counts switches on led and off at end of copunt, its not the tidiest chart but try it and let us know if it works for you
Regards
Dazz
Try the attached chart, basically at 16mhz a count of 31(ish) will = 1/2 sec , so one int triggered ,it counts switches on led and off at end of copunt, its not the tidiest chart but try it and let us know if it works for you
Regards
Dazz
- Fri Oct 10, 2014 5:43 pm
- Forum: General Programming
- Topic: New(edit) Component
- Replies: 12
- Views: 12221
Re: New(edit) Component
hi
the macros you dont use are removed during compiling
Regards
Dazz
the macros you dont use are removed during compiling
Regards
Dazz
- Fri Oct 10, 2014 2:12 pm
- Forum: General Programming
- Topic: Flowcode V5 -> V6
- Replies: 9
- Views: 7650
Re: Flowcode V5 -> V6
Hi
Will this open on your V6
Regards
Dazz
Will this open on your V6
Regards
Dazz
- Thu Oct 09, 2014 5:37 pm
- Forum: Flowcode V6
- Topic: re: Flowcode purchase
- Replies: 6
- Views: 5062
Re: re: Flowcode purchase
Hi
Email the lady who sent the email and see the reasons you need to pay vat,
Regards
Dazz
Email the lady who sent the email and see the reasons you need to pay vat,
Regards
Dazz
- Thu Oct 09, 2014 12:18 pm
- Forum: Flowcode V6
- Topic: Flowcode V6 Ic2
- Replies: 5
- Views: 4150
Re: Flowcode V6 Ic2
HI
What i do is import it into V6, then i simply replace the components with the V6 ones
Regards
Dazz
What i do is import it into V6, then i simply replace the components with the V6 ones
Regards
Dazz
- Thu Oct 09, 2014 12:17 pm
- Forum: Flowcode V6
- Topic: Flowcode 6.1 Released!
- Replies: 46
- Views: 53334
Re: Flowcode 6.1 Released!
Hi Martin
YOu are correct i've just updated ,i was basing it on the beta
Regards
Dazz
YOu are correct i've just updated ,i was basing it on the beta
Regards
Dazz