Page 1 of 1
USB Pic32
Posted: Thu Sep 08, 2016 1:20 pm
by stefan.erni
hi
I wrote a simple program, just initialise the USB (as serial) and send every 3second a "hallo" and led a LED flash.
Compiele und run in the harware is working.
I can generate a usb driver.
But when I connect the USB-cable to the Computer (win7) I can not see a USB Device.
The hardware is an PIC32-PINGUINO-MICRO-REV-B from Olimex.
the controller is an:
Pic32MX440F256H
Re: USB Pic32
Posted: Thu Sep 08, 2016 5:37 pm
by Benj
Hello,
We have not yet tackled USB on the PIC32 range. It is on the list and should hopefully be coming soon hopefully along with other USB improvements.
The USB component info tooltip should help you to know which device families are supported.
Re: USB Pic32
Posted: Fri Sep 09, 2016 2:56 pm
by QMESAR
Benj wrote:We have not yet tackled USB on the PIC32 range
This is bad news for me too,I am developing a low pin count Low cost USB board for PIC32 and was hoping to proto type with FC7
Have good one
Re: USB Pic32
Posted: Fri Sep 09, 2016 7:31 pm
by Benj
I'll see if I can bump this one up the list.
Re: USB Pic32
Posted: Thu Oct 27, 2016 4:12 pm
by stefan.erni
Hi Ben
Is it on the list
?
Or do you have a good idea how to use the usb on PIC 32?
Re: USB Pic32
Posted: Sat Oct 29, 2016 8:39 pm
by QMESAR
stefan.erni wrote:
Is it on the list
?
Or do you have a good idea how to use the usb on PIC 32?
Hi Team,
I am just as excited as Stephan regarding the PIC32 USB stuff
Re: USB Pic32
Posted: Mon Oct 31, 2016 12:20 pm
by Benj
I started to look into this last week. I got slightly further but still not happy with it just yet. Hopefully find some more time this week to finish it off.
Re: USB Pic32
Posted: Thu Nov 10, 2016 9:48 am
by stefan.erni
Hi Ben
Can I have this as beta version?
I can try and help a little.
regards
Stefan
Re: USB Pic32
Posted: Thu Nov 10, 2016 9:05 pm
by Speed64
Hello,
Also has a problem.
FVBUSONION can not be changed to
Controlled by the USB Module
It bounces back.
Win 10 64Bit
Sincerely Uwe
Re: USB Pic32
Posted: Fri Nov 11, 2016 9:25 am
by stefan.erni
Hallo Uwe
Benutzt Du PIC32?
Re: USB Pic32
Posted: Fri Nov 11, 2016 2:53 pm
by Speed64
Moin,
ja, ich benutze einen PIC32.
Ich habe es mit verschiedenen PIC32 versucht.
PIC18F2550 habe ich zum laufen bekommen.
Ich benutze USB CDC.
mit freundlichem Gruß
Uwe
Tel 04499386300
ich rufe gerne zurück
Hello,
Yes, I use a PIC32.
I have tried it with different PIC32.
PIC18F2550 I got to run.
I use USB CDC.
Sincerely
Uwe
Re: USB Pic32
Posted: Fri Nov 11, 2016 3:13 pm
by stefan.erni
Hi Uwe
Usb with Pic 32 is not jet working with flowcode7. Thats what I understand
I hope soon we have a "trial" version.
04499386300
is this number correct?
regards
Stefan
Re: USB Pic32
Posted: Fri Nov 11, 2016 4:20 pm
by QMESAR
Hi Uwe and Stephan
In my understanding too FC7 USB for PIC32 is not working yet however have seen some post by Ben that he is progressing on this so i guess it will be there in the near future
I am also waiting for PIC32 USB support blocks
Gruss
QMESAR
Re: USB Pic32
Posted: Sun Nov 20, 2016 5:04 pm
by Speed64
Hi Benj,
How is it going on?
Sincerely
Speed64