Hi guys,
been away from embedded projects for a while but have a new side project on the go. So I thought I would look at Ghost again.
Is there any guides on using GHOST?
I did not find it all that obvious last time I looked at it a couple of years back.
Any tips or trick on using it?
I'm putting a Flowkit2 on order..
thanks, J.
Learning Ghost
Moderator: Benj
-
- Matrix Staff
- Posts: 9520
- Joined: Sat May 05, 2007 2:27 pm
- Location: Northamptonshire, UK
- Has thanked: 2585 times
- Been thanked: 3815 times
- Contact:
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: Learning Ghost
Hello,
Let us know how you get on with it, we are keen to offer help and support to get more users using this which in turn will help us improve it even more in the future.
Let us know how you get on with it, we are keen to offer help and support to get more users using this which in turn will help us improve it even more in the future.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
- Jay Dee
- Posts: 398
- Joined: Tue Aug 18, 2009 6:42 pm
- Has thanked: 121 times
- Been thanked: 154 times
- Contact:
Re: Learning Ghost
Thanks Guys, Not sure how I missed the Wiki! I have a play about this evening and then with flowkit J.
- Jay Dee
- Posts: 398
- Joined: Tue Aug 18, 2009 6:42 pm
- Has thanked: 121 times
- Been thanked: 154 times
- Contact:
Re: Learning Ghost
Hi Guys,
I have recieved the Flowkit V2, I've had a read of most bits I can find on the datasheets and forum...but a couple of questioins
A) for ICD ICT..which pins are used on the Flowkit to connect the the target's ICD Clock and Data. (typically for a basic PIC B6 & B7)
B) To confirm, do I only need those two pins connected to my target ( obvioulsly + target power )
C) If I am using the traget ICSP pins for programming, can I program through the FlowKit or do I need to swap between programming and ICD devices?
D) If I need to program through the ICSP pins, can I use ANY pins if ICD ICT or am I limited to certain types of pin?
Thanks, J.
I have recieved the Flowkit V2, I've had a read of most bits I can find on the datasheets and forum...but a couple of questioins
A) for ICD ICT..which pins are used on the Flowkit to connect the the target's ICD Clock and Data. (typically for a basic PIC B6 & B7)
B) To confirm, do I only need those two pins connected to my target ( obvioulsly + target power )
C) If I am using the traget ICSP pins for programming, can I program through the FlowKit or do I need to swap between programming and ICD devices?
D) If I need to program through the ICSP pins, can I use ANY pins if ICD ICT or am I limited to certain types of pin?
Thanks, J.
- LeighM
- Matrix Staff
- Posts: 2178
- Joined: Tue Jan 17, 2012 10:07 am
- Has thanked: 481 times
- Been thanked: 699 times
- Contact:
Re: Learning Ghost
Hi,
You should connect the Flowkit pin marked D9 to whatever pin is used as ICD Clock on your target
and the Flowkit pin marked D8 to whatever pin is used as ICD Data on your target.
The Flowkit cannot be used to program the target, it would need to be disconnected.
Hope that helps.
Leigh
You should connect the Flowkit pin marked D9 to whatever pin is used as ICD Clock on your target
and the Flowkit pin marked D8 to whatever pin is used as ICD Data on your target.
The Flowkit cannot be used to program the target, it would need to be disconnected.
Hope that helps.
Leigh
- Jay Dee
- Posts: 398
- Joined: Tue Aug 18, 2009 6:42 pm
- Has thanked: 121 times
- Been thanked: 154 times
- Contact:
Re: Learning Ghost
Hi,
Trying to connect GHOST using flowkit2 with ECIO40P on a EB061 baseboard.
Both programming USB connected and Flowkit pins D8,D9 are connected to the ICSP pins on the baseboard.
D9 > B6 Clock
D8 > B7 Data
I enable the ICD, compile and send to chip.
Press 'play' and I get the "The chip does not contain the latest ICD build" message.
Do I need to set any other settings? or remove the programming USB?
Trying to connect GHOST using flowkit2 with ECIO40P on a EB061 baseboard.
Both programming USB connected and Flowkit pins D8,D9 are connected to the ICSP pins on the baseboard.
D9 > B6 Clock
D8 > B7 Data
I enable the ICD, compile and send to chip.
Press 'play' and I get the "The chip does not contain the latest ICD build" message.
Do I need to set any other settings? or remove the programming USB?