Is the AVR Dragon Programmer and ICD supported?
-NGM
Is the AVR Dragon Programmer Supported?
Moderator: Benj
-
- Posts: 12
- Joined: Wed Jan 30, 2013 5:21 pm
- Has thanked: 1 time
- Contact:
-
- Matrix Staff
- Posts: 9520
- Joined: Sat May 05, 2007 2:27 pm
- Location: Northamptonshire, UK
- Has thanked: 2585 times
- Been thanked: 3815 times
- Contact:
Re: Is the AVR Dragon Programmer Supported?
Please do not post multiple posts on the same topic.
I have deleted your other post asking the same question.
Thank you
I have deleted your other post asking the same question.
Thank you
Martin
-
- Posts: 12
- Joined: Wed Jan 30, 2013 5:21 pm
- Has thanked: 1 time
- Contact:
Re: Is the AVR Dragon Programmer Supported?
I apologize, it was an issue with the refresh in my browser.
-NGM
-NGM
-
- Posts: 1314
- Joined: Sun Jan 15, 2012 3:15 pm
- Has thanked: 474 times
- Been thanked: 458 times
- Contact:
Re: Is the AVR Dragon Programmer Supported?
Hi
It should work, im kinda busy so if you can find a list of command line parameters, and the command line programmer software and post a link i will see if i can figure it out for you, another option is to compile to hex in flowcode then program the hex using avr studio
Regards
Dazz
It should work, im kinda busy so if you can find a list of command line parameters, and the command line programmer software and post a link i will see if i can figure it out for you, another option is to compile to hex in flowcode then program the hex using avr studio
Regards
Dazz
To sign up to the V5 forum follow this link http://www.matrixmultimedia.com/forum_upgrades.php
-
- Posts: 12
- Joined: Wed Jan 30, 2013 5:21 pm
- Has thanked: 1 time
- Contact:
Re: Is the AVR Dragon Programmer Supported?
There are some examples on this page, not sure if it is enough.
http://support.atmel.com/bin/customer.e ... try&id=686
Despite being in the free forum, we now own a full AVR Flow Code 5 version license.
-NGM
http://support.atmel.com/bin/customer.e ... try&id=686
Despite being in the free forum, we now own a full AVR Flow Code 5 version license.
-NGM
-
- Posts: 1314
- Joined: Sun Jan 15, 2012 3:15 pm
- Has thanked: 474 times
- Been thanked: 458 times
- Contact:
Re: Is the AVR Dragon Programmer Supported?
Hi ngm
I will have a look when i've got a spare few minutes, can you sigh=n up to the V5 forum using the link in my sig
Regards
Dazz
I will have a look when i've got a spare few minutes, can you sigh=n up to the V5 forum using the link in my sig
Regards
Dazz
To sign up to the V5 forum follow this link http://www.matrixmultimedia.com/forum_upgrades.php
-
- Posts: 1314
- Joined: Sun Jan 15, 2012 3:15 pm
- Has thanked: 474 times
- Been thanked: 458 times
- Contact:
Re: Is the AVR Dragon Programmer Supported?
Hi
I dont have a dragon but try the programmer setting in your config see image below, this assumes you have the avr dragon command line tool installed, you may have to change the location to suit your pc
Regards
Dazz
I dont have a dragon but try the programmer setting in your config see image below, this assumes you have the avr dragon command line tool installed, you may have to change the location to suit your pc
Regards
Dazz
To sign up to the V5 forum follow this link http://www.matrixmultimedia.com/forum_upgrades.php