View source for Component: TTi Power Supply PL155 P (TTi PL155-P PSU) (3rd Party Equipment/Tools)

From Flowcode Help

← Component: TTi Power Supply PL155 P (TTi PL155-P PSU) (3rd Party Equipment/Tools)

You do not have permission to edit this page, for the following reason:

---

You can view and copy the source of this page.

{| width="50%" |- | width="20%" style="color: gray;" | Author | Paul Newill |- | width="20%" style="color: gray;" | Version | 1.0 (Development) |- | width="20%" style="color: gray;" | Category | 3rd Party Equipment/Tools |} ==[[File:Component Icon 8c08bf29_be7e_4408_92bc_91c476fb70db.png|Image]] TTi Power Supply _ PL155_P (TTi PL155-P PSU) component== TTi PL155-P Power Supply Unit Component. 15V - 5A ==Examples== ''<span style="color:red;">No additional examples</span>'' ==Downloadable macro reference== ''This component does not contain any downloadable macros'' ==Simulation macro reference== ===<span style="font-weight: normal;"><u><tt>LSE</tt></u></span>=== Set the value of LSE <n>, Limit Event Status Register <n>, to <nrf>. '''Parameters''' :[[Variable Types|BYTE]] ''Register'' ::Select Register :[[Variable Types|BYTE]] ''Value'' ::Value to be placed in the register (0-255) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>NOLANOK</tt></u></span>=== Disables the LAn Err message for no LAN connection found at power on if <nrf> is 1 and enables the message if <nrf> is 0. '''Parameters''' :[[Variable Types|BOOL]] ''Status'' ::0 = Message disabled, 1 = Message enabled '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>WAI</tt></u></span>=== Wait for the Operation Complete true. As all commands are completely executed before the next is started this command takes no additional action. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>DELTAV</tt></u></span>=== Set the output <n>voltage step size to <nrf> Volts '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Voltage'' ::Set a Voltage step between 0.0 - 15.0 V '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OVP</tt></u></span>=== Set output <n> over voltage protection trip point to <nrf> Volts '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Voltage'' ::Set a Voltage between 0.0 - 15.0 V '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>DECI</tt></u></span>=== Decrement the output <n> current limit by the step size set for output <n>. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>VRet</tt></u></span>=== Returns the set voltage of output <n> The response is V <n> <nr2><rmt> wjere <nr2> is in Volts. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>SRE</tt></u></span>=== Set the Service Request Enable Register to <nrf>. '''Parameters''' :[[Variable Types|BYTE]] ''Status'' ::Set register value 0-255 '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>PRE</tt></u></span>=== Sets the Parallel Port Enable Register to the value <nrf>. '''Parameters''' :[[Variable Types|BYTE]] ''Status'' ::Set register value 0-255 '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OPALL</tt></u></span>=== Simultaneously sets all ouputs on/off where <nrf> has the following meaning; 0=ALL OFF, 1=ALL ON If OPALL sets all outputs ON then any that were already on will remain ON If OPALL sets all outputs OFF then any that were already off will remain OFF '''Parameters''' :[[Variable Types|BOOL]] ''Status'' ::0=OFF, 1=ON '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>DAMPING</tt></u></span>=== Set the current meter measurement averaging (IAVG) ofoutput <n> where <nrf> has the following meaning: 0 = OFF, 1 = ON. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|BOOL]] ''Status'' ::0 = OFF, 1 = ON '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>DELTAVRet</tt></u></span>=== Returns the output <n> voltage step size. The response is DELTAV<n><nr2><rmt> where <nr2> is in Volts. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>QERRet</tt></u></span>=== Query and clear Query Error Register. The response format is nr1<rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>RATIORet</tt></u></span>=== Query the ratio of output 2 (slave) to putput 1 (master) in tracking mode. The response is <nrf>, where <nrf> is the ratio in percent (0 to 100). '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>IRet</tt></u></span>=== Returns the set current limit of output <n> The response is I <n><nr2><rmt> where <nr2> is in Amps '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>ESRRet</tt></u></span>=== Returns the value in the Standard Event Status Register in <nr1> numeric format. The register is then cleared. The response is <nr1><rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|INT]] ===<span style="font-weight: normal;"><u><tt>PRERet</tt></u></span>=== Returns the value in the Parallel Poll Enable Register in <nr1> numeric format. The syntax of the response is <nr1><rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>DELTAIRet</tt></u></span>=== Returns the output <n> current step size. The response is DELTAI<n><nr2><rmt> where <nr2> is in Amps. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>ESERet</tt></u></span>=== Returns the value in the Standard Event Status Enable Register in <nr1> numeric format. The syntax of the response is <nr1><rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>IRANGERet</tt></u></span>=== Report the current range for output <n>. The response is <nr1><rmt>, where <nr1> is 1 for Low (500mA) range, 2 for High range. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>OCPRet</tt></u></span>=== Returns the current trip setting for output <n> The response is CP<n><nr2><rmt> where <nr2> is in Amps. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>PSUInitialise</tt></u></span>=== This macro is required to initialise the PSU '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>SAV</tt></u></span>=== Save the current set-up of output <n> to the set-up store specified by <nrf> where <nrf> can be 0-9. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|BYTE]] ''StoreLocation'' ::Memory location of register (0-9) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OVPRet</tt></u></span>=== Returns the voltage trip setting for output <n>. The response is VP<n>Mnr2><rmt> where <nr2> is in Volts. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>DELTAI</tt></u></span>=== Set the output <n> current step size to <nrf> Amps '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Current'' ::Set a current step between 0.0 - 5000 mA '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>IFLOCK</tt></u></span>=== Request interface lock. This command requests exclusive access control of the instrument. The response is 1 if successful or -1 if the lock is unavaliable either because it is already in use or the user has disabled this interface from taking control... '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|INT]] ===<span style="font-weight: normal;"><u><tt>TRG</tt></u></span>=== The PSU has no trigger capability. The command is accepted but performs no action. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>LSRRet</tt></u></span>=== Query and clear Limit Event Status Register <n>. The response is <nr1><rmt>. See status reporting section for details. '''Parameters''' :[[Variable Types|BYTE]] ''Register'' ::Select Register number '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>IFLOCKRet</tt></u></span>=== Query the status of the interface lock. The return value is 1 if the lock is owned by the requesting interface instance; 0 ifthere is no active lock or -1 if the lock is unavailable either because it is already in use, or the user has disabled this... '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|INT]] ===<span style="font-weight: normal;"><u><tt>RATIO</tt></u></span>=== Set the ratio of output 2 (slave) to output 1 (master) in tracking mode to <nrf>, where <nrf> is the ratio in percent (0 to 100). '''Parameters''' :[[Variable Types|BYTE]] ''Ratio'' ::Ratio percentage (0-100) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>IORet</tt></u></span>=== Returns the output readback current for output <n> The response is <nr2>A<rmt> where <nr2> is in Amps. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>INCVV</tt></u></span>=== Increment the output <n> voltage by the step size for output <n> and verify. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OPRet</tt></u></span>=== Returns output <n> on/off status The response is <nr1><rmt> where 1 = ON, 0 = OFF. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|BOOL]] : Returns true if the operation is a success, else false ===<span style="font-weight: normal;"><u><tt>LSERet</tt></u></span>=== Return the value of LSE<n>, Limit Status Enable Register <n> - response is <nr1><rmt>. '''Parameters''' :[[Variable Types|BYTE]] ''Register'' ::Select register '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>OCP</tt></u></span>=== Set output <n> over current protection trip point to <nrf> Amps. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''CurrentTrip'' ::Set a current between 0.0 - 5000 mA '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>DECVV</tt></u></span>=== Decrement the output <n> voltage by the step size for output <n> and verify. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>RST</tt></u></span>=== Resets the instrument to the remote control default settings with the exception of all remote interface settings, stored setups, Vmin/Vmax values and Output state at power-on setting. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>VV</tt></u></span>=== Set output <n> to <nrf> Volts with verify. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Voltage'' ::Set a Voltage between 0.0 - 15.0 V '''Return value''' :[[Variable Types|INT]] ===<span style="font-weight: normal;"><u><tt>V</tt></u></span>=== Set output <n> to <nrf> Volts '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Voltage'' ::Set a Voltage between 0.0 - 15.0 V '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>RCL</tt></u></span>=== Recall a set-up for output <n> from he set-up store specified by <nrf> where <nrf> can be 0-9. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|BYTE]] ''StoreLocation'' ::Memory location (0-9) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>INCV</tt></u></span>=== Increment the output <n> voltage by the step size set for output <n>. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>SRERet</tt></u></span>=== Returns the value of the Service Request Enable Register in <nr1> numeric format. The syntax of the response is <nr1><rmt> '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>LOCAL</tt></u></span>=== Go to local. This does not release any active interface lock so that the lock remains with the selected interface when the next remote command is received. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OPC</tt></u></span>=== Sets the Operation Complete bit (bit 0) in the Standard Event Status Register. This will happen immediately the command is executed because of the sequential nature of all operations. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>TRIPRST</tt></u></span>=== Attempt to clear all trip conditions. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>STBRet</tt></u></span>=== Returns the value of the Status Byte Register in <nr1> numeric format. The syntax of the response is <nr1><rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>IFUNLOCK</tt></u></span>=== Release the lock if possible. This command returns the value 0 if successful. If this command is unsuccessful -1 is returned. 200 is placed in the Execution Register and bit 4 of the Event Status Register is set indication that there is no authority... '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|INT]] ===<span style="font-weight: normal;"><u><tt>EERRet</tt></u></span>=== Query and clear Execution Error Register. The response format is nr1 <rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|STRING]] ===<span style="font-weight: normal;"><u><tt>ESE</tt></u></span>=== Sets the Standard Event Status Register to the value of <nrf>. '''Parameters''' :[[Variable Types|BYTE]] ''Status'' ::Set status register to a value of 0-255 '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>CLS</tt></u></span>=== Clear Status. Clears the Status structure. This indirectly clears the Status Byte Register. '''Parameters''' :''This macro has no parameters'' '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>ADDRESSRet</tt></u></span>=== Returns the bus address of the instrument; This is the address used by the GPIB, if fitted, or may be used as a general identifier over the other interfaces. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>DECV</tt></u></span>=== Decrement the output <n> voltage by the step size set for output <n>. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OP</tt></u></span>=== Sets the output <n> on/off where <nrf> has the following meaning: 0=OFF, 1=ON. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|BOOL]] ''Status'' ::0=OFF, 1=ON '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>OPCRet</tt></u></span>=== Query Operation Complete status. The response is always 1<rmt> and will be available immediately the command is executed because all commands are sequential. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BOOL]] : Returns true if the operation is a success, else false ===<span style="font-weight: normal;"><u><tt>ISTRet</tt></u></span>=== Returns IST local message as defined by IEEE Std. 488.2. The syntax of the response is 0<rmt>, if the local message is false, or 1<rmt>, if the local message is true. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BOOL]] : Returns true if the operation is a success, else false ===<span style="font-weight: normal;"><u><tt>TSTRet</tt></u></span>=== The PSU has no self test capability and the response is always 0 <rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BOOL]] : Returns true if the operation is a success, else false ===<span style="font-weight: normal;"><u><tt>VORet</tt></u></span>=== Returns the output readback voltage for output <n> The response is <nr2>V<rmt> where <nr2> is in Volts. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :[[Variable Types|FLOAT]] ===<span style="font-weight: normal;"><u><tt>IRANGE</tt></u></span>=== Sets the current range of output <n> to <nrf>, where <nrf> is 1 for Low (500mA) range, 2 for High range. Output must be switched off before changing range. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|BYTE]] ''Range'' ::1 = Low (500mA), 2 = High (5A) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>IDNRet</tt></u></span>=== Returns the instrument identification. The exact response is determined by the instrument configuration and is of the form <NAME>, <model>, <Serial No.>, <Version>, <rmt>. '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|STRING]] ===<span style="font-weight: normal;"><u><tt>CONFIGRet</tt></u></span>=== Reports the operating mode set by the front panel MODE switch. The syntax of the respnse is <nr1><rmt>, where <nr1> is 1 for single channel units and dual units operating in parallel mode, 2 for dual units with both channels operating independently... '''Parameters''' :''This macro has no parameters'' '''Return value''' :[[Variable Types|BYTE]] ===<span style="font-weight: normal;"><u><tt>INCI</tt></u></span>=== Increment the output <n> current limit by the step size set for output <n>. '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) '''Return value''' :''This call does not return a value'' ===<span style="font-weight: normal;"><u><tt>I</tt></u></span>=== Set output <n> current limit to <nrf> Amps '''Parameters''' :[[Variable Types|BOOL]] ''Output'' ::Choose Output: 1 = Output 1, 2 = Output 2 (if applicable) :[[Variable Types|FLOAT]] ''Current'' ::Set a current between 0 - 5000 mA '''Return value''' :''This call does not return a value'' ==Property reference== <span style="font-weight: normal;"><u>COM Port</u></span> This property is of type ''Fixed list of ints'' and can be referenced with the variable name ''ComPort''. ''<span style="color:red;">No additional information</span>''

Return to Component: TTi Power Supply PL155 P (TTi PL155-P PSU) (3rd Party Equipment/Tools).