I want to make a short distance (5cm or 50mm) Infrared sensor, whose Infrared transmitter can send a specific information or code to Infrared receiver and after receiving this information or code microcontroller will take some action for example it will make one of its pin HIGH. so this way it wont react to modulated signals from any other remote control like a T.V, A.C, stereo etc.
I am using flowcode v5 free version and I have PIC16F877a mcu, I am a novice and evaluating the product I don't know how to get this task done. Its a humble request Please HELP me...
I hope I will get help and support.
Need HELP with Infrared project
- JohnCrow
- Valued Contributor
- Posts: 1367
- Joined: Wed Sep 19, 2007 1:21 pm
- Location: Lincolnshire
- Has thanked: 364 times
- Been thanked: 716 times
- Contact:
Re: Need HELP with Infrared project
Hi okeyzee
Sorry to tell you the IR component is not support in the free versions of FC.
You will need to buy the professional version in addition to the processor pack i.e. PIC to access that component.
The free versions only has the basic components like LED, LCD ADC etc.
Full info is available here
http://www.matrixtsl.com/flowcode.php
You could try the 30day trial of FC6, that way you get all the advanced components for the 30 days, then it resorts to the free version.
Sorry to tell you the IR component is not support in the free versions of FC.
You will need to buy the professional version in addition to the processor pack i.e. PIC to access that component.
The free versions only has the basic components like LED, LCD ADC etc.
Full info is available here
http://www.matrixtsl.com/flowcode.php
You could try the 30day trial of FC6, that way you get all the advanced components for the 30 days, then it resorts to the free version.
1 in 10 people understand binary, the other one doesn't !
Re: Need HELP with Infrared project
Thanks a lot I have downloaded Flowcode V6 30 days-trial, now and I have now access to other MCUs as well...
Ok now coming back to the topic can anyone help me with my project????
Ok now coming back to the topic can anyone help me with my project????
Re: Need HELP with Infrared project
I made this short programme hope I am using the right component.
The data value could be anything I chose a random value 10, what next how to make MCU turn its pin HIGH and glow LED connected to.
The data value could be anything I chose a random value 10, what next how to make MCU turn its pin HIGH and glow LED connected to.
- Attachments
-
- Flowcode2.fcf
- (7 KiB) Downloaded 268 times
- JohnCrow
- Valued Contributor
- Posts: 1367
- Joined: Wed Sep 19, 2007 1:21 pm
- Location: Lincolnshire
- Has thanked: 364 times
- Been thanked: 716 times
- Contact:
Re: Need HELP with Infrared project
Hi
The IrDA board is for data transmission in a similar was to RS232 but using IR
If I understand what you say, you need the RC5 component for what you are doing.
This E-Block with this is a much simpler one to use.
The circuit is a IR diode and IR Transmitter and a resistors / capacitors etc.
I've attached a simple FC5 example This uses my 4 line LCD to show what button is pressed on the remote handset.
The IrDA board is for data transmission in a similar was to RS232 but using IR
If I understand what you say, you need the RC5 component for what you are doing.
This E-Block with this is a much simpler one to use.
The circuit is a IR diode and IR Transmitter and a resistors / capacitors etc.
I've attached a simple FC5 example This uses my 4 line LCD to show what button is pressed on the remote handset.
1 in 10 people understand binary, the other one doesn't !
Re: Need HELP with Infrared project
Thanks John I highly appreciate your quick response.
Your programme will read button pressed on a remote control and display a corresponding value on LCD.
I need to design a programme that will filter all the signals from a remote control in other words it wont respond to any remote controll at all, BUT will only respond to a custom code sent by Ir TX.
In this way it will be immune to all other modulated Ir sources. I am looking for an easier way to do this and hope it is possible with Flowcode.
Solution needed urgently pls Help...
Your programme will read button pressed on a remote control and display a corresponding value on LCD.
I need to design a programme that will filter all the signals from a remote control in other words it wont respond to any remote controll at all, BUT will only respond to a custom code sent by Ir TX.
In this way it will be immune to all other modulated Ir sources. I am looking for an easier way to do this and hope it is possible with Flowcode.
Solution needed urgently pls Help...