HI
Have not used my ARDUINO FLOWKIT 2 for a while using (flow code which used to work fine
But it now appears not to be working correctly giving error message ie after activating icd I have successfully compiled and saved to Arduino but I get
"chip does not contain latest icd build "
Note I also have just tried using my old Flowcode 6 and it works fine with exactly the same hardware
This would perhaps suggest an issue relating to current Flowcode 8 release
Can you please check and advise
Best Regards
FLOWKIT 2
Moderator: Benj
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: FLOWKIT 2
Hello,
We have tried to replicate the problem and so far can't seem to. If you step in rather then clicking play does this make any difference.
Also can you confirm you're not using pins D0 and D1 in your program.
We have tried to replicate the problem and so far can't seem to. If you step in rather then clicking play does this make any difference.
Also can you confirm you're not using pins D0 and D1 in your program.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
-
- Posts: 30
- Joined: Fri Mar 21, 2008 11:16 pm
- Has thanked: 1 time
- Been thanked: 3 times
- Contact:
Re: FLOWKIT 2
Hi
Step into makes no difference
No pins connected to anything except flowkit 2 Arduino
Note using exactly the same hardware (Arduino UNO) and most simple loop program for both the Flowcode 6 and 8 tests
I notice on Flowcode 6 the icd pins are D8 & D9
when run on Flowcode 8 I notice these change to D0 D1
I notice you now cannot change the default icd settings anymore
So
1. Still does not appear to work on current Flowcode 8 any more ideas to resolve
2. Also why did you appear to change the default to DO D1 when running Flowcode 8 as this is used a lot in applications as it is the UNO only hardware serial port
Being able in the past to use D8 D9 was much better as allowed user to still use serial port
Why not allow user to choose the ICD pins to use as before rather than your default
Step into makes no difference
No pins connected to anything except flowkit 2 Arduino
Note using exactly the same hardware (Arduino UNO) and most simple loop program for both the Flowcode 6 and 8 tests
I notice on Flowcode 6 the icd pins are D8 & D9
when run on Flowcode 8 I notice these change to D0 D1
I notice you now cannot change the default icd settings anymore
So
1. Still does not appear to work on current Flowcode 8 any more ideas to resolve
2. Also why did you appear to change the default to DO D1 when running Flowcode 8 as this is used a lot in applications as it is the UNO only hardware serial port
Being able in the past to use D8 D9 was much better as allowed user to still use serial port
Why not allow user to choose the ICD pins to use as before rather than your default
- LeighM
- Matrix Staff
- Posts: 2178
- Joined: Tue Jan 17, 2012 10:07 am
- Has thanked: 481 times
- Been thanked: 699 times
- Contact:
Re: FLOWKIT 2
Well spotted.
Default for clock should be D9 PB1, data should be D8 PB0.
I don't recall us changing these, but that's not what is in the FCDs.
Which particular Uno target are you using (R3, PDIP, SMD?)
I can then edit an FCD version for you to try.
Default for clock should be D9 PB1, data should be D8 PB0.
I don't recall us changing these, but that's not what is in the FCDs.
Which particular Uno target are you using (R3, PDIP, SMD?)
I can then edit an FCD version for you to try.
- LeighM
- Matrix Staff
- Posts: 2178
- Joined: Tue Jan 17, 2012 10:07 am
- Has thanked: 481 times
- Been thanked: 699 times
- Contact:
Re: FLOWKIT 2
Hi,
Please try the attached FCD.
Drop this into directory C:\ProgramData\MatrixTSL\FlowcodeV8\FCD\ARD
Restart Flowcode
Then change your project target to Arduino Uno R3 PDIP Flowkit
Regards,
Leigh
Please try the attached FCD.
Drop this into directory C:\ProgramData\MatrixTSL\FlowcodeV8\FCD\ARD
Restart Flowcode
Then change your project target to Arduino Uno R3 PDIP Flowkit
Regards,
Leigh
- Attachments
-
- Arduino Uno R3 PDIP Flowkit.fcdx
- (14.76 KiB) Downloaded 155 times