Difference between revisions of "MLoader"
From Flowcode Help
Jump to navigationJump to search| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
| − | |||
| − | |||
==Introduction== | ==Introduction== | ||
mLoader is a software application developed by Matrix to reprogram microcontrollers used in a variety of hardware targets. | mLoader is a software application developed by Matrix to reprogram microcontrollers used in a variety of hardware targets. | ||
| + | |||
| + | [[File:mLoader.png|border|caption]] | ||
==Modes of operation== | ==Modes of operation== | ||
| Line 21: | Line 19: | ||
==Supported hardware== | ==Supported hardware== | ||
mLoader currently supports the following hardware: | mLoader currently supports the following hardware: | ||
| − | *'''EB006''' - E-blocks multiprogrammer supporting 8-bit PIC MCUs: | + | *'''EB006''' - E-blocks multiprogrammer supporting 8-bit PIC MCUs: 12Fxxx, 16Fxxx, 18Fxxxx, 18FxxKxx |
| − | + | *'''EB064''' - E-blocks multiprogrammer supporting 16-bit PIC MCUs and dsPIC DSCs: PIC24F, PIC24H, dsPIC30F, dsPIC33F | |
| − | + | *'''EB185''' - E-blocks 32-bit ARM7 programmer | |
| − | + | *'''ECIOs''' - Low-cost, single-board computers: 8-bit PIC MCU, 16-bit dsPIC DSC, 32-bit ARM7 | |
| − | + | *'''MIAC''' - Rugged PLC-like 8-bit PIC MCU | |
| − | *EB064 | + | *'''Formula Flowcode''' - Robot buggy |
| − | + | *'''LK4690L''' - Locktronics USB-programmable PIC MCU | |
| − | + | *'''HP4829''' - USB-programmable Prototype board | |
| − | + | *'''HP1110''' - USB-programmable Project board | |
| − | + | ||
| − | + | ==Supported File Formats== | |
| − | * | + | * '''HEX''' - Intel I32HEX format |
| − | + | * '''S19''' - Motorola S-record (16-bit addresses) | |
| − | + | * '''BIN''' - Raw binary file | |
| − | |||
| − | *ECIOs | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | *MIAC | ||
| − | |||
| − | *Formula Flowcode | ||
| − | * | ||
| − | |||
| − | |||
| − | *HP4829 Prototype board | ||
| − | *HP1110 Project board | ||
==Recent changes== | ==Recent changes== | ||
Recent changes and information on supported chips can be found in the [[mLoader:Recent_Changes]] section of this wiki. | Recent changes and information on supported chips can be found in the [[mLoader:Recent_Changes]] section of this wiki. | ||
Latest revision as of 13:02, 26 January 2015
Contents
Introduction
mLoader is a software application developed by Matrix to reprogram microcontrollers used in a variety of hardware targets.
Modes of operation
There are two basic modes of operation:
- UI mode
- This mode is enabled when mLoader is run as a stand-alone application
- A window is opened (similar to the above image) which allows the user to send and receive programs to the target
- More information can be found here: mLoader:UI_Mode
- non-UI mode
- This mode is typically used when another application (e.g. Flowcode) launches mLoader as part of a build process
- Command line parameters control the operation of mLoader
- No window will usually be opened and use feedback will be provided by the application launching mLoader
- More information can be found here: mLoader:noUI_Mode
Supported hardware
mLoader currently supports the following hardware:
- EB006 - E-blocks multiprogrammer supporting 8-bit PIC MCUs: 12Fxxx, 16Fxxx, 18Fxxxx, 18FxxKxx
- EB064 - E-blocks multiprogrammer supporting 16-bit PIC MCUs and dsPIC DSCs: PIC24F, PIC24H, dsPIC30F, dsPIC33F
- EB185 - E-blocks 32-bit ARM7 programmer
- ECIOs - Low-cost, single-board computers: 8-bit PIC MCU, 16-bit dsPIC DSC, 32-bit ARM7
- MIAC - Rugged PLC-like 8-bit PIC MCU
- Formula Flowcode - Robot buggy
- LK4690L - Locktronics USB-programmable PIC MCU
- HP4829 - USB-programmable Prototype board
- HP1110 - USB-programmable Project board
Supported File Formats
- HEX - Intel I32HEX format
- S19 - Motorola S-record (16-bit addresses)
- BIN - Raw binary file
Recent changes
Recent changes and information on supported chips can be found in the mLoader:Recent_Changes section of this wiki.
